manualshive.com logo in svg

YOKOGAWA ScopeCorder DL750, Руководство пользователя

Поделиться
Скачать
YOKOGAWA ScopeCorder DL750 Скачать руководство пользователя страница 299

19-11

IM 701210-06E

Specifications

19

Video Signal Output (VIDEO OUT (SVGA))

Item

Specifications

Connector type

15-pin D-Sub receptacle

Output type

Analog RGB output

Output resolution

SVGA output 800 

×

 600 dots/60 Hz Vsync

GO/NO-GO Determination I/O (GO/NO-GO)

Item

Specifications

Connector type

Modular jack (RJ-11)

I/O level

START IN input:

TTL (0 to 5 V), SW input possible

GO-OUT/NOGO-OUT: CMOS (0 to 5 V)

Signal

START IN, GO-OUT, and NOGO-OUT

Compatible cable

Four-wire modular cable for telephone lines (GO/NO-GO cable (YOKOGAWA: 366973))

External Start/Stop

1

Item

Specifications

Connector

Shared with the GO/NO-GO start terminal (used exclusively).  Can be used as start/stop input when
GO/NO-GO I/O is not used.

Input

TTL (0 to 5 V) or switch input
Start on low, stop on high

Compatible cable

Four-wire modular cable for telephone lines (GO/NO-GO cable (YOKOGAWA: 366973))

1.

The terminal is also used as a GO/NO-GO Terminal.

COMP Output (Rectangular Signal Output for Probe Compensation)

Item

Specifications

Output frequency

1 kHz

±

1%

Output amplitude

1 V

±

10%

Voice Input/Output (VOICE IN/OUT/SW)

1

Item

Specification

Compatible earphone microphone

Earphone microphone with a PUSH switch (YOKOGAWA: 701951)

Dynamic inner earphone

Input impedance:

32 

Ω

Frequency range:

100 to 20 kHz

Maximum input:

40 mW

Electric condenser microphone

Output impedance:

1.6 k

Ω

Frequency characteristics:

100 to 10 kHz

Directional characteristics:

Omnidirectional

Code:

1.2 m, 

φ

2.5, with 4-pin plug

Weight:

Approx. 16 g

Earphone microphone jack input/output

Jack:

4-pin jack

Microphone input:

Electric condenser microphone, input impedance of approx. 5 k

Ω

Earphone output:

Dynamic, impedance of 32 

Ω

Switch input:

10-k

Ω

 pull-up (3.3 V)

1.

The specifications above apply to the optional earphone microphone with a PUSH switch (701951) that is sold separately.
Operation of other earphone microphones are not guaranteed.

19.9 Auxiliary I/O Section

Содержание ScopeCorder DL750























































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды