manualshive.com logo in svg

YOKOGAWA ScopeCorder DL750, Руководство пользователя

Поделиться
Скачать
YOKOGAWA ScopeCorder DL750 Скачать руководство пользователя страница 217

16-6

IM 701210-06E

DNS (Domain Name System)

DNS is a system used to associate names used on the Internet called host names and

domain names to IP addresses.  (Given AAA.BBBBB.com, AAA is the host name and

BBBBB.com is the domain name.) Instead of using the IP address, which is a sequence

of numbers, host name and domain name can be used to access the network.

On the DL750/DL750P, you can specify the host by name instead of by IP address when

using the FTP client function (see section 16.3) or network printer function (see sections

16.4 and 12.4).

Set the domain name, the DNS server address (“0.0.0.0” by default), and the domain

suffix.  In networks that support DHCP, these settings can be configured automatically.

For details, consult your network administrator.

• DNS Server: DNS Server1/DNS Server2

Up to two DNS server addresses can be specified (primary and secondary).  If the

primary DNS server is down, the secondary DNS server is automatically looked up for

the mapping of the host name/domain name and IP address.

• Domain Suffix: Domain Suffix1/Domain Suffix2

When the IP address corresponding to the server name with the aforementioned

domain name is not found, the system may be set up to search using a different

domain name.  Enter this alternate domain name as the domain suffix.  Up to two

domain suffixes can be specified, Domain Suffix1 (primary), and Domain Suffix2

(secondary).

Note

•

If you changed settings related to the Ethernet network, the DL750/DL750P must be
power cycled.

•

If the DL750/DL750P is turned ON with the DHCP function enabled without an Ethernet
cable connected, communications and file functions may not operate properly.  In this
case, turn DHCP OFF and power cycle the DL750/DL750P.

•

Configuring the TCP/IP Settings of the PC

Communication parameters such as the IP address must also be specified on the PC side.
Communication parameters are specified for each Ethernet NIC that is installed in the PC.
Here, the settings of the NIC for connecting your PC and the DL750/DL750P are
explained.
If the IP address and other parameters are to be obtained dynamically using the DHCP
server, the following settings are not necessary.  In this case, select 

Obtain an IP

address automatically

 under the 

IP Address

 tab of the 

TCP/IP Properties

 dialog box.

For example, if you are connecting a PC and the DL750/DL750P to an independent
Ethernet network, you can specify parameters as indicated in the next table.
For details on the parameters, consult your system or network administrator.

Parameter

Value

Remarks

IP address

Example: 192.168.21.128

IP address for the PC

Subnet mask

Example: 255.255.255.0

Set the same value as the subnet mask
that was specified for the DL750/DL750P.

Gateway

None

DNS

Disable

WINS

Disable

The following procedure describes the steps for Windows 95/98/ME.  For Windows NT/
2000 Pro/XP, carry out equivalent steps accordingly.
1. Choose 

Settings

 > 

Control Panel

 from the 

Start

 menu to open the Control Panel

folder.

2. Double-click the 

Network

 icon to display the following network setup dialog box.

3. Select the 

TCP/IP

 corresponding to the Ethernet NIC that is connected to the PC and

click 

Properties

 to display the TCP/IP properties setup dialog box.

16.2 Setting up the TCP/IP

Содержание ScopeCorder DL750























































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды