YASKAWA SGM7D-30F Скачать руководство пользователя | Manualshive

Страница: 270 / 502

background image

3.4 Command Option Attachable-type FT82 SERVOPACKs with INDEXER Modules

3.4.9 Troubleshooting Based on the Operation and Conditions of the Servomotor

3

Maintenance

3-201

Absolute
Encoder
Position
Deviation
Error (The
position
that was
saved in the
host con-
troller when
the power
was turned
OFF is dif-
ferent from
the posi-
tion when
the power
was next
turned ON.)

Noise interference occurred
because of incorrect Encoder
Cable specifications.

Check the Encoder Cable
to see if it satisfies speci-
fications. Use a shielded
twisted-pair wire cable or
a screened twisted-pair
cable with conductors of
at least 0.12 mm

2

.

Use cables that satisfy
the specifications.

–

Noise interference occurred
because the Encoder Cable
is too long.

Check the length of the
Encoder Cable.

Rotary Servomotors:
The Encoder Cable
length must be 50 m
max.

–

Noise interference occurred
because the Encoder Cable
is damaged.

Check the Encoder Cable
to see if it is pinched or
the sheath is damaged.

Replace the Encoder
Cable and correct the
cable installation envi-
ronment.

–

Noise interference occurred
because the Encoder Cable
is damaged.

Check to see if the
Encoder Cable is bundled
with a high-current line or
installed near a high-cur-
rent line.

Correct the cable lay-
out so that no surge is
applied by high-current
lines.

–

There is variation in the FG
potential because of the
influence of machines on the
Servomotor side, such as a
welder.

Check to see if the
machines are correctly
grounded.

Properly ground the
machines to separate
them from the FG of
the encoder.

–

There is a SERVOPACK
pulse counting error due to
noise.

Check to see if there is
noise interference on the
I/O signal line from the
encoder or Serial Con-
verter Unit.

Implement counter-
measures against noise
for the encoder or
Serial Converter Unit
wiring.

–

The encoder was subjected
to excessive vibration or
shock.

Check to see if vibration
from the machine
occurred.
Check the Servomotor
installation (mounting sur-
face precision, securing
state, and alignment).

Reduce machine vibra-
tion. Or, improve the
mounting conditions of
the Servomotor.

–

A failure occurred in the
encoder.

–

Replace the Servomo-
tor.

–

A failure occurred in the SER-
VOPACK.

–

Replace the SERVO-
PACK.

–

Continued on next page.

Continued from previous page.

Problem

Possible Cause

Confirmation

Correction

Reference

«
...
268
269
270
271
272
...
»

Содержание SGM7D-30F























































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SGM7D-30F

DS3 series servo

Бренд: Xinje Страницы: 120

Бренд: National Instruments Страницы: 35

Бренд: Becker Страницы: 28

Бренд: Becker Страницы: 24

Бренд: Becker Страницы: 36

Бренд: CENTENT Страницы: 36

Бренд: Sealey Страницы: 2

VFD-ME300 Series

Бренд: Delta Страницы: 2

VFD-EL-W Series

Бренд: Delta Страницы: 197

Бренд: Delta Страницы: 756

Бренд: Leadshine Страницы: 27

Бренд: Franklin Electric Страницы: 28

590 DRV Digital

Бренд: Eurotherm Drives Страницы: 318

Бренд: YASKAWA Страницы: 67

ADAP-KOOL Drive

Бренд: Danfoss Страницы: 262

Бренд: Danfoss Страницы: 172

Бренд: Danfoss Страницы: 26

SIMUTECH SIMVFD

Бренд: TPC Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды