YASKAWA SGM7D-30F Скачать руководство пользователя

Страница: 315 / 502

3.5 FT83 SERVOPACKs with Analog Voltage/Pulse Train References

3.5.8 INDEXER Warning Displays and Troubleshooting

3-246

E4DE

A.9F9

Moving Disabled
Error due to P-LS

The specified target position exceeds the
position reference of forward software limit
set in Pn638.

•

Check the tar-
get position
specification.

•

Check the for-
ward software
limit in Pn638.

•

Check the Mov-
ing Mode (rota-
tional/linear
coordinates)
(Pn637=
n.



•

If the software
limits are not
being used,
select rotational
coordinates with
Pn637=
n.



X (Mov-

ing Mode) or dis-
able the
software limits
by setting Pn638
= Pn63A = 0.

E4EE

A.9F9

Moving Disabled
Error due to N-LS

The specified target position exceeds the
position reference of reverse software limit
set in Pn63A.

•

Check the tar-
get position
specification.

•

Check the
reverse soft-
ware limit in
Pn63A.

•

Check the set-
ting of the Mov-
ing Mode
(rotational/linear
coordinates)
(Pn637=
n.



X).

•

If the software
limits are not
being used,
select rotational
coordinates for
the (i.e., set
Pn637 to
n.



1) or dis-

able the soft-
ware limits by
setting Pn638 =
Pn63A = 0.

E4FE

A.9F9

Position Refer-
ence Out-of-range
Error

The Moving Mode is set to rotational coordi-
nates (i.e., Pn637 is not set to n.



0) and

the target position designation exceeded the
position range setting (Pn638 and Pn63A).

•

Check the tar-
get position
specification.

•

Check the posi-
tioning range set
with Pn638 and
Pn63A.

•

Check the set-
ting of the Mov-
ing Mode
(rotational/linear
coordinates)
(Pn637=
n.



X).

Continued on next page.

Continued from previous page.

Error No.

Alarm

Number

Error Name

Meaning

Corrective Action

Содержание SGM7D-30F























































































































































































































































































































































































































































































































Результаты поиска

Содержание SGM7D-30F

Отзывы:

Похожие инструкции для SGM7D-30F

Бренды по названию

Популярные бренды

YASKAWA SGM7D-30F, Руководство по эксплуатации продукта

Результаты поиска

Содержание SGM7D-30F

Отзывы:

Похожие инструкции для SGM7D-30F

Бренды по названию

Популярные бренды