manualshive.com logo in svg

YASKAWA SGM7D-30F, Руководство по эксплуатации продукта

YASKAWA SGM7D-30F - электрический серводвигатель высокой производительности. Доступ к бесплатному руководству пользователя "Product Manual" для настройки и установки можно найти на сайте manualshive.com. Скачайте руководство для использования всей функциональности этого продукта.

Поделиться
Скачать
background image

3.4  Command Option Attachable-type FT82 SERVOPACKs with INDEXER Modules

3.4.3  Troubleshooting Alarms

3-158

A.330: 

Main Circuit 
Power Supply 
Wiring Error 
(Detected when 
the main circuit 
power supply is 
turned ON.)

The regenerative 
resistor was discon-
nected when the 
SERVOPACK power 
supply voltage was 
high.

Measure the resistance 
of the regenerative 
resistor using a measur-
ing instrument.

If you are using the regen-
erative resistor built into 
the SERVOPACK, replace 
the SERVOPACK.
If you are using an Exter-
nal Regenerative Resis-
tor, replace the External 
Regenerative Resistor.

–

DC power was sup-
plied when an AC 
power supply input 
was specified in the 
settings.

Check the power sup-
ply to see if it is a DC 
power supply.

Correct the power supply 
setting to match the 
actual power supply.

*1

AC power was sup-
plied when a DC 
power supply input 
was specified in the 
settings.

Check the power sup-
ply to see if it is an AC 
power supply.

Correct the power supply 
setting to match the 
actual power supply.

Pn600 (Regenerative 
Resistor Capacity) is 
not set to 0 and an 
External Regenerative 
Resistor is not con-
nected to an SGD7S-
2R8A SERVOPACKs.

Check it see if an Exter-
nal Regenerative Resis-
tor is connected and 
check the setting of 
Pn600.

Connect an External 
Regenerative Resistor, or 
if an External Regenera-
tive Resistor is not 
required, set Pn600 to 0.

*1

A failure occurred in 
the SERVOPACK.

–

The SERVOPACK may be 
faulty. Replace the SER-
VOPACK.

–

A.400: 

Overvoltage 
(Detected in the 
main circuit 
power supply 
section of the 
SERVOPACK.)

The power supply 
voltage exceeded the 
specified range.

Measure the power 
supply voltage.

Set the AC/DC power 
supply voltage within the 
specified range.

–

The power supply is 
not stable or was 
influenced by a light-
ning surge.

Measure the power 
supply voltage.

Improve the power sup-
ply conditions, install a 
surge absorber, and then 
turn the power supply 
OFF and ON again. If an 
alarm still occurs, the 
SERVOPACK may be 
faulty. Replace the SER-
VOPACK.

–

The voltage for AC 
power supply was too 
high during accelera-
tion or deceleration.

Check the power sup-
ply voltage and the 
speed and torque 
during operation.

Set the AC power supply 
voltage within the speci-
fied range.

–

The external regener-
ative resistance is too 
high for the operating 
conditions.

Check the operating 
conditions and the 
regenerative resistance.

Select a regenerative 
resistance value that is 
appropriate for the oper-
ating conditions and load.

*4

The moment of inertia 
ratio or mass ratio 
exceeded the allow-
able value.

Check to see if the 
moment of inertia ratio 
or mass ratio is within 
the allowable range.

Increase the deceleration 
time, or reduce the load.

–

A failure occurred in 
the SERVOPACK.

–

While the main circuit 
power supply is OFF, turn 
the control power supply 
to the SERVOPACK OFF 
and ON again. If an alarm 
still occurs, the SERVO-
PACK may be faulty. 
Replace the SERVO-
PACK.

–

Continued on next page.

Continued from previous page.

Alarm Number: 

Alarm Name

Possible Cause

Confirmation

Correction

Reference

Содержание SGM7D-30F























































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SGM7D-30F

KEB COMBIVERT F5 Instructions For Use Manual preview
COMBIVERT F5
Бренд: KEB Страницы: 40
Graco 16E778 Installation Instructions preview
16E778
Бренд: Graco Страницы: 4
Becker enocean R8-17 Assembly And Operating Instructions Manual preview
enocean R8-17
Бренд: Becker Страницы: 28
Becker C16 Assembly And Operating Instructions Manual preview
C16
Бренд: Becker Страницы: 24
Becker P5-20-C18 PLUS Assembly And Operating Instructions Manual preview
P5-20-C18 PLUS
Бренд: Becker Страницы: 36
DoorHan DRIVE SHAFT-50PRO Installation And Service Instruction preview
DRIVE SHAFT-50PRO
Бренд: DoorHan Страницы: 18
Parker PSD1-S Manual preview
PSD1-S
Бренд: Parker Страницы: 20
HAUTAU PRIMAT-E Kompakt 190 Mounting Instructions preview
PRIMAT-E Kompakt 190
Бренд: HAUTAU Страницы: 16
Baldor BC141 Installation & Operating Manual preview
BC141
Бренд: Baldor Страницы: 20
Kinco 2S User Guidance preview
2S
Бренд: Kinco Страницы: 30
Kinco CV100 Series Manual preview
CV100 Series
Бренд: Kinco Страницы: 119
Danfoss VLT CANopen MCA 105 Programming Manual preview
VLT CANopen MCA 105
Бренд: Danfoss Страницы: 50
Danfoss VLT CDS 303 Operating Instructions Manual preview
VLT CDS 303
Бренд: Danfoss Страницы: 172
Parker Compax3 C3I20T11 Operating Instructions Manual preview
Compax3 C3I20T11
Бренд: Parker Страницы: 430
KEB COMBIVERT F6 Instruction Manual preview
COMBIVERT F6
Бренд: KEB Страницы: 48
Panasonic MINAS-A5BL Series Manual preview
MINAS-A5BL Series
Бренд: Panasonic Страницы: 206
ABB ACS 160 User Manual preview
ACS 160
Бренд: ABB Страницы: 138
ABB ACS 1013-A1 User Manual preview
ACS 1013-A1
Бренд: ABB Страницы: 186

Бренды по названию

Популярные бренды

Загрузить еще бренды