YASKAWA SGM7D-30F Скачать руководство пользователя страница 74

Страница: 74 / 502

3.1 FT82 SERVOPACKs with Analog Voltage/Pulse Train References

3.1.2 List of Alarms

Maintenance

3-5

A.550

Maximum Speed Setting
Error

The setting of Pn385 (Maxi-
mum Motor Speed) is greater
than the maximum motor
speed.

Gr.1

Yes

A.710

Instantaneous Overload

The Servomotor was operat-
ing for several seconds to
several tens of seconds
under a torque that largely
exceeded the rating.

Gr.2

Yes

A.720

Continuous Overload

The Servomotor was operat-
ing continuously under a
torque that exceeded the rat-
ing.

Gr.1

Yes

A.730

Dynamic Brake Overload

When the dynamic brake was
applied, the rotational or lin-
ear kinetic energy exceeded
the capacity of the dynamic
brake resistor.

Gr.1

Yes

A.731

A.740

Inrush Current Limiting
Resistor Overload

The main circuit power sup-
ply was frequently turned ON
and OFF.

Gr.1

Yes

A.7A1

Internal Temperature Error
1 (Control Board Tempera-
ture Error)

The surrounding tempera-
ture of the control PCB is
abnormal.

Gr.2

Yes

A.7A2

Internal Temperature Error
2 (Power Board Tempera-
ture Error)

The surrounding tempera-
ture of the power PCB is
abnormal.

Gr.2

Yes

A.7A3

Internal Temperature Sen-
sor Error

An error occurred in the tem-
perature sensor circuit.

Gr.2

A.7Ab

SERVOPACK Built-in Fan
Stopped

The fan inside the SERVO-
PACK stopped.

Gr.1

Yes

A.810

Encoder Backup Alarm

The power supplies to the
encoder all failed and the
position data was lost.

Gr.1

A.820

Encoder Checksum Alarm

There is an error in the
checksum results for
encoder memory.

Gr.1

A.830

Encoder Battery Alarm

The battery voltage was
lower than the specified level
after the control power sup-
ply was turned ON.

Gr.1

Yes

A.840

Encoder Data Alarm

There is an internal data error
in the encoder.

Gr.1

A.850

Encoder Overspeed

The encoder was operating
at high speed when the
power was turned ON.

Gr.1

A.860

Encoder Overheated

The internal temperature of
the rotary encoder or linear
encoder is too high.

Gr.1

A.861

Motor Overheated

The internal temperature of
motor is too high.

Gr.1

Continued on next page.

Continued from previous page.

Alarm
Number

Alarm Name

Alarm Meaning

Servo-

motor

Stop-

ping

Method

Alarm
Reset

Possi-

ble?

Alarm Code

Output

ALO1 ALO2 ALO3

Содержание SGM7D-30F























































































































































































































































































































































































































































































































Результаты поиска

Содержание SGM7D-30F

Отзывы:

Бренды по названию

Популярные бренды

YASKAWA SGM7D-30F, Руководство по эксплуатации продукта

Результаты поиска

Содержание SGM7D-30F

Отзывы:

Бренды по названию

Популярные бренды