YASKAWA SGM7D-30F страница 200 Скачать руководство пользователя

Страница: 200 / 502

3.3 FT82 SERVOPACK with MECHATROLINK-III Communications References

3.3.6 Troubleshooting Warnings

Maintenance

3-131

A.901:

Position Deviation
Overflow Alarm at
Servo ON

The position devi-
ation when the
servo was turned
ON exceeded the
percentage set
with the following
formula:
(Pn526

Pn528/

100)

–

Optimize the setting of
Pn528 (Excessive Position
Error Warning Level at
Servo ON).

–

A.910:

Overload (warning
before an A.710 or
A.720 alarm occurs)

The wiring is not
correct or there is
a faulty contact in
the motor or
encoder wiring.

Check the wiring.

Make sure that the Servo-
motor and encoder are cor-
rectly wired.

–

Operation was
performed that
exceeded the
overload protec-
tion characteris-
tics.

Check the motor over-
load characteristics
and Run command.

Reconsider the load and
operating conditions. Or,
increase the motor capacity.

–

An excessive load
was applied
during operation
because the Ser-
vomotor was not
driven because of
mechanical prob-
lems.

Check the operation
reference and motor
speed.

Remove the mechanical
problem.

–

The overload
warning level
(Pn52B) is not
suitable.

Check that the over-
load warning level
(Pn52B) is suitable.

Set a suitable overload
warning level (Pn52B).

A failure occurred
in the SERVO-
PACK.

–

The SERVOPACK may be
faulty. Replace the SERVO-
PACK.

–

A.911:

Vibration

Abnormal vibra-
tion was detected
during motor
operation.

Check for abnormal
motor noise, and check
the speed and torque
waveforms during
operation.

Reduce the motor speed.
Or, reduce the servo gain
with custom tuning.

The setting of
Pn103 (Moment of
Inertia Ratio) is
greater than the
actual moment of
inertia or was
greatly changed.

Check the moment of
inertia ratio or mass
ratio.

Set Pn103 (Moment of Iner-
tia Ratio) to an appropriate
value.

The vibration
detection level
(Pn312 or Pn384)
is not suitable.

Check that the vibra-
tion detection level
(Pn312 or Pn384) is
suitable.

Set a suitable vibration
detection level (Pn312 or
Pn384).

Continued on next page.

Continued from previous page.

Warning Number:

Warning Name

Possible Cause

Confirmation

Correction

Reference

Содержание SGM7D-30F























































































































































































































































































































































































































































































































Результаты поиска

Содержание SGM7D-30F

Отзывы:

Похожие инструкции для SGM7D-30F

Бренды по названию

Популярные бренды

YASKAWA SGM7D-30F, Руководство по эксплуатации продукта

Результаты поиска

Содержание SGM7D-30F

Отзывы:

Похожие инструкции для SGM7D-30F

Бренды по названию

Популярные бренды