YASKAWA SGM7D-30F страница 120 Скачать руководство пользователя | Manualshive

Страница: 120 / 502

background image

3.2 FT82 SERVOPACK with MECHATROLINK-II Communications References

3.2.2 List of Alarms

3

Maintenance

3-51

A.041

Encoder Output Pulse
Setting Error

The setting of Pn212 (Encoder Output Pulses) or
Pn281 (Encoder Output Resolution) is outside of
the setting range or does not satisfy the setting
conditions.

Gr.1

No

A.042

Parameter Combination
Error

The combination of some parameters exceeds
the setting range.

Gr.1

No

A.044

Semi-Closed/Fully-Closed
Loop Control Parameter
Setting Error

The settings of the Option Module and Pn002 =
n.X



(External Encoder Usage) do not

match.

Gr.1

No

A.04A

Parameter Setting Error 2

There is an error in the bank members or bank
data settings.

Gr.1

No

A.050

Combination Error

The capacities of the SERVOPACK and Servomo-
tor do not match.

Gr.1

Yes

A.051

Unsupported Device
Alarm

An unsupported device was connected.

Gr.1

No

A.0b0

Invalid Servo ON Com-
mand Alarm

The SV_ON (Servo ON) command was sent from
the host controller after a utility function that turns
ON the Servomotor was executed.

Gr.1

Yes

A.100

Overcurrent Detected

An overcurrent flowed through the power trans-
former or the heat sink overheated.

Gr.1

No

A.101

Motor Overcurrent
Detected

The current to the motor exceeded the allowable
current.

Gr.1

No

A.300

Regeneration Error

There is an error related to regeneration.

Gr.1

Yes

A.320

Regenerative Overload

A regenerative overload occurred.

Gr.2

Yes

A.330

Main Circuit Power Supply
Wiring Error

•

The AC power supply input setting or DC power
supply input setting is not correct.

•

The power supply wiring is not correct.

Gr.1

Yes

A.400

Overvoltage

The main circuit DC voltage is too high.

Gr.1

Yes

A.410

Undervoltage

The main circuit DC voltage is too low.

Gr.2

Yes

A.510

Overspeed

The motor exceeded the maximum speed.

Gr.1

Yes

A.511

Encoder Output Pulse
Overspeed

The pulse output speed for the setting of Pn212
(Encoder Output Pulses) was exceeded.

Gr.1

Yes

A.520

Vibration Alarm

Abnormal oscillation was detected in the motor
speed.

Gr.1

Yes

A.521

Autotuning Alarm

Vibration was detected during autotuning for the
tuning-less function.

Gr.1

Yes

A.550

Maximum Speed Setting
Error

The setting of Pn385 (Maximum Motor Speed) is
greater than the maximum motor speed.

Gr.1

Yes

A.710

Instantaneous Overload

The Servomotor was operating for several sec-
onds to several tens of seconds under a torque
that largely exceeded the rating.

Gr.2

Yes

A.720

Continuous Overload

The Servomotor was operating continuously
under a torque that exceeded the rating.

Gr.1

Yes

A.730

Dynamic Brake Overload

When the dynamic brake was applied, the rota-
tional or linear kinetic energy exceeded the
capacity of the dynamic brake resistor.

Gr.1

Yes

A.731

A.740

Inrush Current Limiting
Resistor Overload

The main circuit power supply was frequently
turned ON and OFF.

Gr.1

Yes

A.7A1

Internal Temperature Error
1 (Control Board Tempera-
ture Error)

The surrounding temperature of the control PCB
is abnormal.

Gr.2

Yes

Continued on next page.

Continued from previous page.

Alarm
Number

Alarm Name

Alarm Meaning

Servo-

motor

Stop-

ping

Method

Alarm
Reset

Possi-

ble?

«
...
118
119
120
121
122
...
»

Содержание SGM7D-30F























































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SGM7D-30F

Бренд: Xinje Страницы: 121

Бренд: ANTEK Страницы: 18

TRINORM 436 Series

Бренд: Emerson Страницы: 6

Бренд: Nord Drivesystems Страницы: 212

Бренд: Masterflex Страницы: 32

CDC-0252 1-TMS+ Series

Бренд: Dyer Страницы: 8

PullMaster PH136

Бренд: Dover Страницы: 33

Бренд: V&T Страницы: 79

Бренд: Applied Motion Products Страницы: 2

Бренд: Applied Motion Products Страницы: 8

Бренд: YASKAWA Страницы: 1016

SGD7C-***AMAA***

Бренд: YASKAWA Страницы: 669

Бренд: Xinje Страницы: 50

Fcontrol FTET4AHMQ

Бренд: ZIEHL-ABEGG Страницы: 46

Бренд: Danfoss Страницы: 82

Бренд: Granite Devices Страницы: 6

Бренд: Granite Devices Страницы: 14

VLT Micro Drive PK18

Бренд: Danfoss Страницы: 97

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды