YASKAWA SGM7D-30F Скачать руководство пользователя страница 301 | Manualshive

Страница: 301 / 502

YASKAWA SGM7D-30F Скачать руководство пользователя страница 301

3.5 FT83 SERVOPACKs with Analog Voltage/Pulse Train References

3.5.3 Troubleshooting Alarms

3-232

A.Eb1:

Safety Function
Signal Input Tim-
ing Error

The delay between
activation of the
/HWBB1 and
/HWBB2 input sig-
nals for the HWBB
was ten second or
longer.

Measure the time delay
between the /HWBB1
and /HWBB2 signals.

The output signal circuits
or devices for /HWBB1
and /HWBB2 or the SER-
VOPACK input signal cir-
cuits may be faulty.
Alternatively, the input sig-
nal cables may be discon-
nected. Check to see if
any of these items are
faulty or have been dis-
connected.

–

A failure occurred in
the SERVOPACK.

–

Replace the SERVO-
PACK.

–

A.EC8:

Gate Drive Error 1
(An error
occurred in the
gate drive circuit.) A failure occurred in

the SERVOPACK.

–

Turn the power supply to
the SERVOPACK OFF and
ON again. If an alarm still
occurs, the SERVOPACK
may be faulty. Replace the
SERVOPACK.

–

A.EC9:

Gate Drive Error 2
(An error
occurred in the
gate drive circuit.)

A.EF9:

INDEXER Alarm

An alarm occurred in
the INDEXER.

Use the S to
identify the INDEXER
alarm.

Use the correction for the
INDEXER alarm.

*1

A.F10:

Power Supply
Line Open Phase
(The voltage was
low for more than
one second for
phase R, S, or T
when the main
power supply
was ON.)

The three-phase
power supply wiring is
not correct.

Check the power sup-
ply wiring.

Make sure that the power
supply is correctly wired.

*1

The three-phase
power supply is
unbalanced.

Measure the voltage for
each phase of the
three-phase power sup-
ply.

Balance the power sup-
ply by changing phases.

–

A single-phase power
supply was input with-
out specifying a sig-
nal-phase AC power
supply input (Pn00B =
n.



1



).

Check the power sup-
ply and the parameter
setting.

Match the parameter set-
ting to the power supply.

*1

A failure occurred in
the SERVOPACK.

–

Turn the power supply to
the SERVOPACK OFF and
ON again. If an alarm still
occurs, the SERVOPACK
may be faulty. Replace the
SERVOPACK.

–

A.F50:

Servomotor Main
Circuit Cable Dis-
connection
(The Servomotor
did not operate or
power was not
supplied to the
Servomotor even
though the /S-ON
signal was input
when the Servo-
motor was ready
to receive it.)

A failure occurred in
the SERVOPACK.

–

The SERVOPACK may be
faulty. Replace the SER-
VOPACK.

–

The wiring is not cor-
rect or there is a faulty
contact in the motor
wiring.

Check the wiring.

Make sure that the Servo-
motor is correctly wired.

*1

Continued on next page.

Continued from previous page.

Alarm Number:

Alarm Name

Possible Cause

Confirmation

Correction

Reference

«
...
299
300
301
302
303
...
»

Содержание SGM7D-30F























































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды