YASKAWA SGM7D-30F Скачать руководство пользователя | Manualshive

Страница: 185 / 502

background image

3.3 FT82 SERVOPACK with MECHATROLINK-III Communications References

3.3.3 Troubleshooting Alarms

3-116

A.861:

Motor Over-
heated

The surrounding tem-
perature around the
Servomotor is too
high.

Measure the surround-
ing temperature around
the Servomotor.

Reduce the surrounding
air temperature of the
Servomotor to 40

°

or less.

–

The motor load is
greater than the rated
load.

Check the load with the
accumulated load ratio
on the Motion Monitor
Tab Page on the Sig-
maWin+.

Operate the Servo Drive
so that the motor load
remains within the speci-
fied range.

*1

A failure occurred in
the Serial Converter
Unit.

–

Turn the power supply to
the SERVOPACK OFF and
ON again. If an alarm still
occurs, the Serial Con-
verter Unit may be faulty.
Replace the Serial Con-
verter Unit.

–

A failure occurred in
the SERVOPACK.

–

Turn the power supply to
the SERVOPACK OFF and
ON again. If an alarm still
occurs, the SERVOPACK
may be faulty. Replace the
SERVOPACK.

–

A.862:

Overheat Alarm

The surrounding tem-
perature is too high.

Check the surrounding
temperature using a
thermostat.

Lower the surrounding
temperature by improving
the installation conditions
of the machine.

–

The overheat protec-
tion input signal line is
disconnected or
short-circuited.

Check the input voltage
with the overheat pro-
tection input information
on the Motion Monitor
Tab Page on the Sig-
maWin+.

Repair the line for the
overheat protection input
signal.

–

An overload alarm
was reset by turning
OFF the power sup-
ply too many times.

Check the alarm display
to see if there is an
overload alarm.

Change the method for
resetting the alarm.

–

Operation was per-
formed under an
excessive load.

Use the accumulated
load ratio to check the
load during operation.

Reconsider the load and
operating conditions.

–

A failure occurred in
the SERVOPACK.

–

The SERVOPACK may be
faulty. Replace the
SERVOPACK.

–

The sensor attached
to the machine is
faulty.

–

The sensor attached to
the machine may be
faulty. Repair the sensor
attached to the machine.

–

A.8A0:

External Encoder
Error

Setting the origin of
the absolute linear
encoder failed
because the motor
moved.

Before you set the ori-
gin, use the fully-closed
feedback pulse counter
to confirm that the
motor is not moving.

The motor must be
stopped while setting the
origin position.

*1

A failure occurred in
the external encoder.

–

Replace the external
encoder.

–

A.8A1:

External Encoder
Module Error

A failure occurred in
the external encoder.

–

Replace the external
encoder.

–

A failure occurred in
the Serial Converter
Unit.

–

Replace the Serial Con-
verter Unit.

–

Continued on next page.

Continued from previous page.

Alarm Number:

Alarm Name

Possible Cause

Confirmation

Correction

Reference

«
...
183
184
185
186
187
...
»

Содержание SGM7D-30F























































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SGM7D-30F

AF-650 GP Series

Бренд: GE Страницы: 212

Бренд: BAREL Страницы: 8

Бренд: Eaton Страницы: 96

ANT95LZS Series

Бренд: Aerotech Страницы: 48

Rexroth EFC 3600

Бренд: Bosch Страницы: 238

Rexroth IndraDrive FC Series

Бренд: Bosch Страницы: 72

Rexroth Hagglunds DOb

Бренд: Bosch Страницы: 80

REXROTH IndraDrive

Бренд: Bosch Страницы: 437

Rexroth EcoDrive Cs DKC-004 Series

Бренд: Bosch Страницы: 45

VS-616PS5 Series

Бренд: YASKAWA Страницы: 113

Бренд: YASKAWA Страницы: 434

T-Verter E2 Series

Бренд: TECO Страницы: 64

Бренд: Kollmorgen Страницы: 3

Бренд: Kollmorgen Страницы: 183

Бренд: Kollmorgen Страницы: 29

SubDrive Inline 1100

Бренд: Franklin Electric Страницы: 13

Бренд: Minolta Страницы: 26

Бренд: Becker Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды