YASKAWA SGM7D-30F Скачать руководство пользователя

Страница: 276 / 502

3.5 FT83 SERVOPACKs with Analog Voltage/Pulse Train References

3.5.2 List of Alarms

Maintenance

3-207

A.710

Instantaneous Over-
load

The Servomotor was operating for several
seconds to several tens of seconds under
a torque that largely exceeded the rating.

Gr.2

Yes

A.720

Continuous Overload

The Servomotor was operating continu-
ously under a torque that exceeded the
rating.

Gr.1

Yes

A.730

Dynamic Brake Over-
load

When the dynamic brake was applied,
the rotational or linear kinetic energy
exceeded the capacity of the dynamic
brake resistor.

Gr.1

Yes

A.731

A.740

Inrush Current Limit-
ing Resistor Overload

The main circuit power supply was fre-
quently turned ON and OFF.

Gr.1

Yes

A.7A1

Internal Temperature
Error 1 (Control Board
Temperature Error)

The surrounding temperature of the con-
trol PCB is abnormal.

Gr.2

Yes

A.7A2

Internal Temperature
Error 2 (Power Board
Temperature Error)

The surrounding temperature of the
power PCB is abnormal.

Gr.2

Yes

A.7A3

Internal Temperature
Sensor Error

An error occurred in the temperature sen-
sor circuit.

Gr.2

A.7Ab

SERVOPACK Built-in
Fan Stopped

The fan inside the SERVOPACK stopped.

Gr.1

Yes

A.810

Encoder Backup
Alarm

The power supplies to the encoder all
failed and the position data was lost.

Gr.1

A.820

Encoder Checksum
Alarm

There is an error in the checksum results
for encoder memory.

Gr.1

A.830

Encoder Battery
Alarm

The battery voltage was lower than the
specified level after the control power
supply was turned ON.

Gr.1

Yes

A.840

Encoder Data Alarm

There is an internal data error in the
encoder.

Gr.1

A.850

Encoder Overspeed

The encoder was operating at high speed
when the power was turned ON.

Gr.1

A.860

Encoder Overheated

The internal temperature of encoder is
too high.

Gr.1

A.861

Motor Overheated

The internal temperature of motor is too
high.

Gr.1

A.862

Overheat Alarm

The input voltage (temperature) for the
overheat protection input (TH) signal
exceeded the setting of Pn61B (Overheat
Alarm Level).

Gr.1

Yes

A.8A0

External Encoder
Error

An error occurred in the external encoder.

Gr.1

Yes

A.8A1

External Encoder
Module Error

An error occurred in the Serial Converter
Unit.

Gr.1

Yes

A.8A2

External Incremental
Encoder Sensor Error

An error occurred in the external encoder.

Gr.1

Yes

A.8A3

External Absolute
Encoder Position
Error

An error occurred in the position data of
the external encoder.

Gr.1

Yes

A.8A5

External Encoder
Overspeed

An overspeed error occurred in the exter-
nal encoder.

Gr.1

Yes

A.8A6

External Encoder
Overheated

An overheating error occurred in the
external encoder.

Gr.1

Yes

Continued on next page.

Continued from previous page.

Alarm
Number

Alarm Name

Alarm Meaning

Servo-

motor

Stop-

ping

Method

Alarm
Reset

Possi-

ble?

Alarm Code Output

/ALO1 /ALO2 /ALO3

Содержание SGM7D-30F























































































































































































































































































































































































































































































































Результаты поиска

Содержание SGM7D-30F

Отзывы:

Похожие инструкции для SGM7D-30F

Бренды по названию

Популярные бренды

YASKAWA SGM7D-30F, Руководство по эксплуатации продукта

Результаты поиска

Содержание SGM7D-30F

Отзывы:

Похожие инструкции для SGM7D-30F

Бренды по названию

Популярные бренды