YASKAWA SGM7D-30F Скачать руководство пользователя | Manualshive

Страница: 259 / 502

background image

3.4 Command Option Attachable-type FT82 SERVOPACKs with INDEXER Modules

3.4.8 INDEXER Module Error Displays and Troubleshooting

3-190

E43E

A.A9F

JOG Speed Table
Save Failure Error

While writing data to the flash memory, a
failure occurred during one of the following
operation.

•

While saving a JOG speed table by using
a JSPDSTORE command

•

While saving a JOG speed table by using
FnB05

•

While initializing a JOG speed table by
using a JSPDINIT command

•

While initializing a JOG speed table by
using FnB08

Repair the hard-
ware.

E44E

A.A9F

Canceled Pro-
gram Table Error

There was a request to start program table
operation even though an E19A or E1BA
alarm occurred when the control power
supply was turned ON.

Remove the
cause of the
alarm.

E46E

A.A9F

Canceled JOG
Speed Table Error

There was a request to start JOG speed
table operation even though an E1FA or
E22A alarm occurred when the control
power supply was turned ON.

Remove the
cause of the
alarm.

E47E

A.A9F

Serial Communi-
cations Receiv-
ing Buffer
Overflow Error

There was an overflow in the reception buf-
fer used for serial commands.

•

An error will occur if too many serial com-
mands are sent consecutively without
waiting for the responses.
(Normally, the reception buffer will not
overflow if there is command/response
handshaking.)

•

When an overflow has occurred, error
code E47E will be returned and all of the
data that has accumulated in the recep-
tion buffer will be discarded.

Wait for a
response to be
received before
sending the next
command.
The reception
buffer can con-
tain up to 100
commands.

E48E

A.A9F

Serial Communi-
cations Parity
Error

A parity check error occurred with the serial
command.

•

This error will occur if even parity is not
being used.

•

The command that caused this error will
be discarded and no response will be
returned.

•

There will be no response, but the
/WARN output and LED indicators will
indicate that an error has occurred.

•

Check the serial
communica-
tions protocol
(PnB00) and bit
rate (PnB01)
settings.

•

Check the wir-
ing.

•

If noise may be
causing the
problem, take
steps to reduce
noise such as
using commu-
nications
cables with fer-
rite cores.

Continued on next page.

Continued from previous page.

Serial

Command

Negative

Response

Alarm

Number

Error Name

Meaning

Corrective Action

«
...
257
258
259
260
261
...
»

Содержание SGM7D-30F























































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SGM7D-30F

Бренд: Duratech Страницы: 39

Бренд: B-K lighting Страницы: 10

Бренд: ABB Страницы: 20

Бренд: Koheron Страницы: 3

Бренд: STG-BEIKIRCH Страницы: 27

Fcontrol FKDMxx-C Series

Бренд: ZIEHL-ABEGG Страницы: 74

Бренд: ABB Страницы: 116

VLT AutomationDrive FC 360

Бренд: Danfoss Страницы: 88

Бренд: Parallax Страницы: 8

Бренд: MAIMAN ELECTRONICS Страницы: 20

Бренд: Parker Страницы: 150

Бренд: Veichi Страницы: 136

ACH550-01+B055+F278

Бренд: ABB Страницы: 28

Бренд: ICAN Страницы: 16

Бренд: Pacific Scientific Страницы: 60

Бренд: Pacific Scientific Страницы: 84

Бренд: Pacific Scientific Страницы: 90

Бренд: Pacific Scientific Страницы: 199

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды