manualshive.com logo in svg

YASKAWA SGM7D-30F, Руководство по эксплуатации продукта

Поделиться
Скачать
YASKAWA SGM7D-30F Скачать руководство пользователя страница 218

3.4  Command Option Attachable-type FT82 SERVOPACKs with INDEXER Modules

 3.4.2  List of Alarms

3

Maintenance

3-149

A.C91

Encoder Communica-
tions Position Data 
Acceleration Rate 
Error

An error occurred in calculating the posi-
tion data of the encoder.

Gr.1

No

L

H

L

A.C92

Encoder Communica-
tions Timer Error

An error occurred in the communications 
timer between the encoder and SERVO-
PACK.

Gr.1

No

A.CA0

Encoder Parameter 
Error

The parameters in the encoder are cor-
rupted.

Gr.1

No

A.Cb0

Encoder Echoback 
Error

The contents of communications with the 
encoder are incorrect.

Gr.1

No

A.CC0

Multiturn Limit Dis-
agreement

Different multiturn limits have been set in 
the encoder and the SERVOPACK.

Gr.1

No

A.CF1

Reception Failed Error 
in Feedback Option 
Module Communica-
tions

Receiving data from the Feedback Option 
Module failed.

Gr.1

No

A.CF2

Timer Stopped Error 
in Feedback Option 
Module Communica-
tions

An error occurred in the timer for commu-
nications with the Feedback Option Mod-
ule.

Gr.1

No

A.d00

Position Deviation 
Overflow

The setting of Pn520 (Excessive Position 
Deviation Alarm Level) was exceeded by 
the position deviation while the servo was 
ON.

Gr.1

Yes

L

L

H

A.d01

Position Deviation 
Overflow Alarm at 
Servo ON

The servo was turned ON after the posi-
tion deviation exceeded the setting of 
Pn526 (Excessive Position Deviation 
Alarm Level at Servo ON) while the servo 
was OFF.

Gr.1

Yes

A.d02

Position Deviation 
Overflow Alarm for 
Speed Limit at Servo 
ON

If position deviation remains in the devia-
tion counter, the setting of Pn529 or 
Pn584 (Speed Limit Level at Servo ON) 
limits the speed when the servo is turned 
ON. This alarm occurs if a position refer-
ence is input and the setting of Pn520 
(Excessive Position Deviation Alarm Level) 
is exceeded before the limit is cleared.

Gr.2

Yes

A.d10

Motor-Load Position 
Deviation Overflow

There was too much position deviation 
between the motor and load during fully-
closed loop control.

Gr.2

Yes

A.d30

Position Data Over-
flow

The position feedback data exceeded 

±

1,879,048,192.

Gr.1

No

A.E00

Command Option 

Module IF Initializa-
tion 

Timeout Error

Communications initialization failed 
between the SERVOPACK and the Com-
mand Option Module.

Gr.2

Yes

H

L

L

A.E02

Command Option 

Module IF 

Synchroni-

zation Error 1

An synchronization error occurred 
between the SERVOPACK and the Com-
mand Option Module.

Gr.1

Yes

A.E03

Command Option 

Module IF Communi-
cations Data 

Error

An error occurred in the data of commu-
nications between the SERVOPACK and 
the Command Option Module.

Gr.1

Yes

A.E70

Command Option 

Module Detection 

Failure

Detection of the Command Option Mod-
ule failed.

Gr.1

No

Continued on next page.

Continued from previous page.

Alarm 
Number

Alarm Name

Alarm Meaning

Servo-

motor 

Stop-

ping 

Method

Alarm 
Reset 

Possi-

ble?

Alarm Code Output

/ALO1 /ALO2 /ALO3

Содержание SGM7D-30F























































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды