YASKAWA SGM7D-30F Скачать руководство пользователя

Страница: 150 / 502

3.2 FT82 SERVOPACK with MECHATROLINK-II Communications References

3.2.5 List of Warnings

Maintenance

3-81

Note: 1. A warning code is not output unless you set Pn001 to n.1



(Output both alarm codes and warning

codes).

2. Use Pn008 = n.





(Warning Detection Selection) to control warning detection.

However, the following warnings are not affected by the setting of Pn008 = n.





and other parameter

settings are required in addition to Pn008 = n.





A.95A

Command Warning 1
(Unsatisfied Com-
mand Conditions)

A command was sent when the conditions for sending a command were
not satisfied.

A.95b

Command Warning 2
(Unsupported Com-
mand)

An unsupported command was sent.

A.95d

Command Warning 4
(Command Interfer-
ence)

There was command interference, particularly latch command interfer-
ence.

A.95E

Command Warning 5
(Subcommand Not
Possible)

The subcommand and main command interfere with each other.

A.95F

Command Warning 6
(Undefined Command)

An undefined command was sent.

A.960

MECHATROLINK
Communications
Warning

A communications error occurred during MECHATROLINK communica-
tions.

A.971

Undervoltage

This warning occurs before an A.410 alarm (Undervoltage) occurs. If the
warning is ignored and operation is continued, an alarm may occur.

A.9A0

Overtravel

Overtravel was detected while the servo was ON.

A.9b0

Preventative Mainte-
nance Warning

One of the consumable parts has reached the end of its service life.

Warning

Parameters That Must Be Set to Select Warning Detection

A.911

Pn310 = n.



X (Vibration Detection Setting)

A.923

–
(Not affected by the setting of Pn008 = n.





A.930

Pn008 = n.



X (Low Battery Voltage Alarm/Warning Selection)

A.942

Pn423 = n.





(Speed Ripple Compensation Information Disagreement Warning

Detection Selection)

A.94A to A.960

Pn800=n.





(Warning Check Masks)

A.971

Pn008 = n.



X (Low Battery Voltage Alarm/Warning Selection)

(Not affected by the setting of Pn008 = n.





A.9A0

Pn00D = n.X



(Overtravel Warning Detection Selection)

(Not affected by the setting of Pn008 = n.





A.9b0

Pn00F = n.



X (Preventative Maintenance Selection)

Continued from previous page.

Warning

Number

Warning Name

Meaning

Содержание SGM7D-30F























































































































































































































































































































































































































































































































Результаты поиска

Содержание SGM7D-30F

Отзывы:

Похожие инструкции для SGM7D-30F

Бренды по названию

Популярные бренды

YASKAWA SGM7D-30F, Руководство по эксплуатации продукта

Результаты поиска

Содержание SGM7D-30F

Отзывы:

Похожие инструкции для SGM7D-30F

Бренды по названию

Популярные бренды