YASKAWA SGM7D-30F Скачать руководство пользователя | Manualshive

Страница: 20 / 502

background image

xx



Storage Precautions



Transportation Precautions

NOTICE



Do not attempt to use a SERVOPACK or Servomotor that is damaged or that has missing parts.



Install external emergency stop circuits that shut OFF the power supply and stops operation
immediately when an error occurs.



In locations with poor power supply conditions, install the necessary protective devices (such as
AC reactors) to ensure that the input power is supplied within the specified voltage range.

There is a risk of damage to the SERVOPACK.



Use a Noise Filter to minimize the effects of electromagnetic interference.

Electronic devices used near the SERVOPACK may be affected by electromagnetic interference.



Always use a Servomotor and SERVOPACK in one of the specified combinations.



Do not touch a SERVOPACK or Servomotor with wet hands.

There is a risk of product failure.

C

A

UTION



Do not place an excessive load on the product during storage. (Follow all instructions on the
packages.)

There is a risk of injury or damage.

NOTICE



Do not install or store the product in any of the following locations.

•

Locations that are subject to direct sunlight

•

Locations that are subject to ambient temperatures that exceed product specifications

•

Locations that are subject to relative humidities that exceed product specifications

•

Locations that are subject to condensation as the result of extreme changes in temperature

•

Locations that are subject to corrosive or flammable gases

•

Locations that are near flammable materials

•

Locations that are subject to dust, salts, or iron powder

•

Locations that are subject to water, oil, or chemicals

•

Locations that are subject to vibration or shock that exceeds product specifications

•

Locations that are subject to radiation

If you store or install the product in any of the above locations, the product may fail or be damaged.

C

A

UTION



Transport the product in a way that is suitable to the mass of the product.



Do not use the eyebolts on a SERVOPACK or Servomotor to move the machine.

There is a risk of damage or injury.



When you handle a SERVOPACK or Servomotor, be careful of sharp parts, such as the corners.

There is a risk of injury.



Do not place an excessive load on the product during transportation. (Follow all instructions on
the packages.)

There is a risk of injury or damage.

«
...
18
19
20
21
22
...
»

Содержание SGM7D-30F























































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SGM7D-30F

Бренд: ABB Страницы: 16

Бренд: ABB Страницы: 4

Бренд: ABB Страницы: 52

Бренд: Injung Tech Страницы: 16

Бренд: CENTENT Страницы: 39

Бренд: Leadshine Страницы: 15

Бренд: Unimotion Страницы: 7

Бренд: Shihlin Страницы: 4

Бренд: electrogas Страницы: 10

Бренд: ZIEHL-ABEGG Страницы: 24

Бренд: Applied Motion Products Страницы: 44

Бренд: Eurotherm Drives Страницы: 79

Бренд: Ridder Страницы: 52

Бренд: Danfoss Страницы: 241

Бренд: Lenze Страницы: 199

Бренд: elero Страницы: 8

CMMT-ST-C8-1C Series

Бренд: Festo Страницы: 58

PowerXL DM1 Series

Бренд: Eaton Страницы: 102

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды