YASKAWA SGM7D-30F Скачать руководство пользователя страница 155 | Manualshive

Страница: 155 / 502

YASKAWA SGM7D-30F Скачать руководство пользователя страница 155

3.2 FT82 SERVOPACK with MECHATROLINK-II Communications References

3.2.6 Troubleshooting Warnings

3-86

A.93B:

Overheat Warning

The surrounding
temperature is too
high.

Check the surrounding
temperature using a
thermostat.

Lower the surrounding tem-
perature by improving the
installation conditions of the
machine.

–

Operation was
performed under
an excessive load.

Use the accumulated
load ratio to check the
load during operation.

Reconsider the load and
operating conditions.

–

A failure occurred
in the SERVO-
PACK.

–

The SERVOPACK may be
faulty. Replace the SERVO-
PACK.

–

The sensor
attached to the
machine is faulty.

–

The sensor attached to the
machine may be faulty.
Repair the sensor attached
to the machine.

–

A.942:

Speed Ripple Com-
pensation Informa-
tion Disagreement

The speed ripple
compensation
information stored
in the encoder
does not agree
with the speed
ripple compensa-
tion information
stored in the SER-
VOPACK.

–

Reset the speed ripple
compensation value on the
S.

*

–

Set Pn423 to n.



1



(Do

not detect A.942 alarms).
However, changing the set-
ting may increase the speed
ripple.

*

–

Set Pn423 to n.



0

(Disable torque ripple com-
pensation). However,
changing the setting may
increase the speed ripple.

*

A.94A:

Data Setting Warn-
ing 1 (Parameter
Number Error)

An invalid param-
eter number was
used.

Check the command
that caused the warn-
ing.

Use the correct parameter
number.

*

A.94b:

Data Setting Warn-
ing 2 (Out of Range)

The set com-
mand data was
clamped to the
minimum or maxi-
mum value of the
setting range.

Check the command
that caused the warn-
ing.

Set the parameter within
the setting range.

*

A.94C:

Data Setting Warn-
ing 3 (Calculation
Error)

The calculation
result of the set-
ting is not correct.

Check the command
that caused the warn-
ing.

Set the parameter within
the setting range.

*

A.94d:

Data Setting Warn-
ing 4 (Parameter
Size)

The parameter
size set in the
command is not
correct.

Check the command
that caused the warn-
ing.

Set the correct parameter
size.

*

A.94E:

Data Setting Warn-
ing 5 (Latch Mode
Error)

A latch mode error
was detected.

Check the command
that caused the warn-
ing.

Change the setting of
Pn850 or the LT_MOD data
for the LTMOD_ON com-
mand sent by the host con-
troller to an appropriate
value.

*

A.95A:

Command Warning
1 (Unsatisfied Com-
mand Conditions)

The command
conditions are not
satisfied.

Check the command
that caused the warn-
ing.

Send the command after
the command conditions
are satisfied.

*

A.95b:

Command Warning
2 (Unsupported
Command)

An unsupported
command was
received.

Check the command
that caused the warn-
ing.

Do not send unsupported
commands.

*

Continued on next page.

Continued from previous page.

Warning Number:

Warning Name

Possible Cause

Confirmation

Correction

Reference

«
...
153
154
155
156
157
...
»

Содержание SGM7D-30F























































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды