manualshive.com logo in svg

Toshiba e-STUDIO350, Руководство по обслуживанию, Страница: 84 / 286

Поделиться
Скачать
Toshiba e-STUDIO350 Скачать руководство пользователя страница 84

e-STUDIO350/450 GENERAL OPERATION

4 - 6

November 2003 © TOSHIBA TEC

4

4.3 Detection of Abnormality

When something abnormal has occurred in the equipment, the symbols corresponding to the type of

abnormality are displayed.

4.3.1 Types of abnormality

A)

Abnormality cleared without turning OFF the door switch

(1) Add paper

(2) Paper misfeed in bypass

B)

Abnormality not cleared without turning OFF the door switch

(1) Misfeed in equipment

(2) Add toner

(3) Developer unit not installed properly

(4) Toner bag replacement

C)

Abnormality not cleared without turning OFF the main switch

(1) Call for service

(3)

After the interruption copying is finished:

•

LED “INTERRUPT” OFF by pressing the [INTERRUPT] button

•

Equipment returns to the status before the interruption

•

“Ready to resume job 1” is displayed

(4) Press the [START] button

The copying operation before the interruption is resumed.

Содержание e-STUDIO350































































































































































































































































































Отзывы:

Нет отзывов