manualshive.com logo in svg

Toshiba e-STUDIO350, Руководство по обслуживанию, Страница: 244 / 286

Поделиться
Скачать
Toshiba e-STUDIO350 Скачать руководство пользователя страница 244

e-STUDIO350/450  FUSER UNIT / PAPER EXIT SECTION

13 - 20

November 2003 © TOSHIBA TEC

13

Fig. 13-719

[H] Pressure roller 

(1) Take off the cleaning unit ( 

 Chapter 13.7

[G]).

(2) Remove the pressure springs on both front

and rear sides.

(3) Pull out the pressure lever units on both left

and right sides.

(4) Take out the pressure roller.

(9) Remove 1 C-ring and take off the cleaning

roller with the whole bushings on both sides.

(10) Take off the bushings from the cleaning roller.

Fig. 13-720

[I]

IH coil

(1) Take off the fuser unit ( 

 Chapter 13.7 [A]).

(2) Take off  the fuser unit cover

( 

 Chapter 13.7 [B]).

(3) Release the harness from the harness guide

of the cover on the rear side.

(4) Remove 1 screw and take off the cover on

the rear side.

Fig. 13-718

Fig. 13-717

Содержание e-STUDIO350































































































































































































































































































Отзывы:

Нет отзывов