manualshive.com logo in svg

Toshiba e-STUDIO350, Руководство по обслуживанию, Страница: 38 / 286

Поделиться
Скачать
Toshiba e-STUDIO350 Скачать руководство пользователя страница 38

e-STUDIO350/450  OUTLINE OF THE MACHINE

2 - 22

November 2003 © TOSHIBA TEC

2

2.4.2   Construction of boards

(a)

Construction diagram of boards

This system consists of the following including the SYS board as a main board.

: DC power supply line

: AC power supply line

: Signal line

AC input

Main switch

Cover opening/closing
interlock  switch

SYS

PS-ACC

FIL

or

FUS

LGC

CCD

INV

SLG

Scanner unit

KEY

DSP

Control panel

NIC

ADU

SFB

HVT

IH

LDR

LRL

SNS

Laser unit

(b)

Function of each board

CCD board:

This is the board to convert the reflected light by the original to electrical signals. It consists of the

CCD, and its peripheral circuitry. The CCD converts the reflected light by the original to analog signal

and outputs it to the SLG board.

SLG board:

This is the board to mainly control the scanning function (scanner unit) and consists of the Scanner-

CPU, ASIC, memory (Flash ROM and SRAM), A/D converter, driver for motor drive, etc. When

scanning the original, the exposure lamp and scan motor are driven by the command from the

Scanner-CPU. The analog signal output from the CCD board is then converted to digital signal by

the A/D converter. Image processing is performed by ASIC.

INV board:

This is the board on which the lighting control circuit of the exposure lamp is mounted. The exposure

lamp lights by the command from the Scanner-CPU.

DSP board:

This is the board to mainly control the control panel. The panel processing CPU detecting the input

from each button and touch panel, and the lighting control circuit for the backlight of the LCD are

mounted. And it relays the control signal of the control panel from the SYS board to the LCD and KEY

board.

Fig. 2-402

Содержание e-STUDIO350































































































































































































































































































Отзывы:

Нет отзывов