Toshiba e-STUDIO350 Скачать руководство пользователя страница 145

Страница: 145 / 286

November 2003 © TOSHIBA TEC

8 - 5

e-STUDIO350/450 LASER OPTICAL UNIT

(3)

lenses-1 and -2

These two lenses perform the following adjustment on the laser beam reflected by the polygonal

mirror.

a. Uniform-velocity scanning

Since the polygonal mirror is rotating at a

uniform velocity, the laser beam reflected

from the mirror scans over the drum sur-

face at a uniform angular velocity; namely,

the pitch between the dots on the drum is

wider at both ends than at the center of the

scanning range. The f

lenses help to cor-

rect this difference, making all the dot-to-

dot pitches equal on the drum surface.

b. Face tilt correction

The reflecting face of the polygonal mirror

is tilted slightly to one side against the per-

fect vertical. Horizontal deviation of the

laser beam which is caused by the tilt is

corrected.

c. Sectional shape of laser beam

The shape of the laser beam spotted on

the drum is adjusted.

(4)

H-Sync signal detection PC board

The laser beam which is started to be scanned from one of the reflected plane of the polygonal

mirror is reflected by the H-Sync detection mirror and enters the PIN diode on the H-Sync signal

detection PC board. The primary scanning synchronizing signal is generated based on this reflec-

tion.

Fig. 8-203

Fig. 8-204

Wider

Narrower

Drum

fØ Lens-1

fØ Lens-2

Same intervals

Mirror plane is tilted.

Deviation

Содержание e-STUDIO350






























































































































































































































































































Результаты поиска

Содержание e-STUDIO350

Отзывы:

Toshiba e-STUDIO350, Руководство по обслуживанию, Страница: 145 / 286

Результаты поиска

Содержание e-STUDIO350

Отзывы: