Toshiba e-STUDIO350 Скачать руководство пользователя страница 122

Страница: 122 / 286

e-STUDIO350/450 SCANNER

6 - 14

November 2003 © TOSHIBA TEC

(4)

Original size is determined by the combination of the signals output from each detection point.

Combination charts for size determination of A4 series and LT series are as follows.

When the platen sensor is OFF,

•

The followings are determined by output signals from the APS sensors.

Size (The combination of the signals satisfy any in the above chart)

:Size is displayed on the control panel and a specific paper or reproduction ratio is selected.

Size retention (The combination of the signals do not satisfy the above chart)

:The latest original size recognized (or no original state) until new paper size is recognized.

No original (Output from all the sensors are “H”.)

:Reproduction ratio and paper are not selected.

•

Size change is always observed and detected.

•

The carriage-1 stays at the standby position even if the reproduction ratio changes corresponding to the

change of the original size.

When the platen sensor is ON,

The latest original size (or no original state) recognized right before the platen sensor is turned ON is re-

tained regardless of the status the APS sensor output signals.

APS-2

APS-1

APS-C

APS-R

APS-3

Size judgement

A4-R

B5-R

A5-R

[A4 Series]

APS-2

APS-C

APS-R

APS-3

Size judgement

LT-R

ST-R

[LT Series]

Code

Output signal

Original

Not available

Available

Содержание e-STUDIO350






























































































































































































































































































Результаты поиска

Содержание e-STUDIO350

Отзывы:

Toshiba e-STUDIO350, Руководство по обслуживанию, Страница: 122 / 286

Результаты поиска

Содержание e-STUDIO350

Отзывы: