manualshive.com logo in svg

Toshiba e-STUDIO350, Руководство по обслуживанию, Страница: 190 / 286

Поделиться
Скачать
Toshiba e-STUDIO350 Скачать руководство пользователя страница 190

e-STUDIO350/450  DRUM RELATED SECTON

11 - 2

November 2003 © TOSHIBA TEC

11

11.2 Functions

(1)

Drum

The drum is made of a cylindrical aluminum base coated with thin film of organic photoconductive

substance.

The photoconductive object becomes insulative (the electrical resistance is high) when it is not

exposed to the light and electrically conductive (the electrical resistance is low) when it is exposed to

the light. This object is called a photoconductor.

(2)

Main charger

The main charger consists of a metal rod with U-shaped section, insulated blocks at both ends of the

rod and charger wire attached between them.

When a high voltage is applied to the charger wire, the air around it is charged (ionized). The ionized

air then flows into the drum causing it to be charged. This phenomenon is called “corona discharge”.

Negative charge caused by the corona discharge and grid is applied to the drum surface evenly in

dark place. The main charger is equipped with a wire cleaner to clean the wire.

(3)

Cleaner

(a) Cleaning blade

This blade is pressed against the drum surface with a constant force by the pressure springs, and

scrapes off the residual toner from the drum surface.

(b) Recovery blade

This blade catches the toner scraped off by the cleaning blade.

(c) Toner recovery auger

This auger carries the residual toner scraped off to the toner bag.

(d) Toner bag full detection sensor -1

The sensor detects the toner bag full when it is pushed by the toner recovery auger in the

cleaner which is given a pressure from the used toner in the toner bag.

Содержание e-STUDIO350































































































































































































































































































Отзывы:

Нет отзывов