Toshiba e-STUDIO350 Скачать руководство пользователя страница 101

Страница: 101 / 286

November 2003 © TOSHIBA TEC

5 - 7

e-STUDIO350/450 CONTROL PANEL

No.

Message

State of equipment

Note

Misfeed in copier

Call for service

Please try again after

a while

Set standard size

Paper jam in the equipment

- Displayed when paper jam occurred in the

equipment

Displayed when motor, sensor, switch, etc.

do not work properly

Displayed when the Department Code can

no be keyed in immediately after power-ON.

Displayed when the paper size which is not

acceptable is set (depends on the setting)

Remove the paper in the equipment

according to the messages displayed

on the panel.

Turn OFF the power and solve the

problem, then turn ON the power.

Leave it for a while and key in the

code again

Reset the paper size.

Содержание e-STUDIO350






























































































































































































































































































Результаты поиска

Содержание e-STUDIO350

Отзывы:

Toshiba e-STUDIO350, Руководство по обслуживанию, Страница: 101 / 286

Результаты поиска

Содержание e-STUDIO350

Отзывы: