Toshiba e-STUDIO350 Скачать руководство пользователя страница 215

Страница: 215 / 286

November 2003 © TOSHIBA TEC

12 - 7

e-STUDIO350/450 DEVELOPMENT SYSTEM

12.4.3 Adjustment using the temperature / humidity sensor

Variation in the output (V

ATS

) of the auto-toner sensor due to humidity is corrected using the temperature

/ humidity sensor to maintain the toner density in the developer material at a certain amount.

12.4.4 Adjustment using the drum thermistor

Variation in the output (V

ATS

) of the auto-toner sensor due to temperature is corrected using the drum

thermistor to maintain the toner density in the developer material at a certain amount.

Feedback control by drum thermistor in setting mode (08)

Item to be controlled

Toner output control by drum thermistor

Code

08-840

Default

Содержание e-STUDIO350






























































































































































































































































































Результаты поиска

Содержание e-STUDIO350

Отзывы:

Toshiba e-STUDIO350, Руководство по обслуживанию, Страница: 215 / 286

Результаты поиска

Содержание e-STUDIO350

Отзывы: