manualshive.com logo in svg

Toshiba e-STUDIO350, Руководство по обслуживанию, Страница: 232 / 286

Поделиться
Скачать
Toshiba e-STUDIO350 Скачать руководство пользователя страница 232

e-STUDIO350/450  FUSER UNIT / PAPER EXIT SECTION

13 - 8

November 2003 © TOSHIBA TEC

13

13.4.5 Temperature detection section

To maintain the stable temperature of the fuser belt, the thermistor detects the temperature and controls
ON/OFF of the IH coil. Output from the thermistors is used to detect the abnormality.

(1) Relation between the thermistor output voltage and surface temperature of the fuser belt

Fig. 13-404

(3) Temperature control for the both ends of the fuser roller

During the continuous printing, the temperature of the both ends of the fuser belt (areas where the
paper does not pass on) generally tend to be higher than that of the other areas (areas where the
paper passes on). The temperature of the ends are detected by the front edge thermistor, and
when it reaches 280°C, the heater is automatically turned OFF regardless of the temperature of the
area where the paper passes on.

(2) Control of the surface temperature of the fuser belt

Output voltages of thermistors [V]

Approx. 0.5

Approx. 2.0

Approx. 3.5

Approx. 4.0

Surface temperatures of fuser belt [

o

C]

40

100

160

200

°

C

200

0

Ready (200

°

C)

Warming-up

Temperature
of fuser roller

During printing (200

°

C)

OFF

IH coil ON

ON

OFF ON OFF

ON

OFF

OFF

ON

ON

Содержание e-STUDIO350































































































































































































































































































Отзывы:

Нет отзывов