manualshive.com logo in svg

Toshiba e-STUDIO350, Руководство по обслуживанию, Страница: 226 / 286

Поделиться
Скачать
Toshiba e-STUDIO350 Скачать руководство пользователя страница 226

e-STUDIO350/450  FUSER UNIT / PAPER EXIT SECTION

13 - 2

November 2003 © TOSHIBA TEC

13

13.3 Functions

(1) IH coil (IH: Induction Heating)

The IH coil is inside the fuser roller and applies the induction heating to the fuser roller. The coil is
fixed at a position and does not move when the fuser roller is rotating.

(2) Fuser roller

The fuser roller is a metal roller which generates heat spontaneously with eddy current produced by
the electromagnetic induction of IH coil. The fuser roller is heated by this self-heating of this roller,
and then the toner is fused on the paper.

(3) Pressure roller

The pressure roller is a sponge roller which assures the nip amount between the fuser roller. The
pressure arm and spring press the fuser roller.
The toner is fused effectively by the pressure of this roller.

(4) Separation fingers

The separation fingers are installed, five above the pressure roller and six above the fuser roller, in
order to separate the paper adhered on each roller.

(5) Cleaning roller

The cleaning roller is a fluorinated metal roller which removes the residual toner and paper dust
adhered on the pressure roller.

(6) Main thermistor

This thermistor detects the temperature of the fuser roller to maintain it in a certain temperature
range (actually around 200°C) between the lower limit causing the poor fusing and the upper limit
causing the high temperature offsetting. When the temperature of the fuser roller is lower than the
preset temperature, it turns ON the power supply to the IH coil, and when it is higher than the preset
temperature, it cuts off the supply.

(7) Edge thermistor

It detects the temperature abnormality at the both ends of the fuser roller. This area may be over-
heated without heat absorption by paper since paper does not pass through this area. This ther-
mistor is not related to the temperature control of the fuser roller.

Содержание e-STUDIO350































































































































































































































































































Отзывы:

Нет отзывов