Toshiba e-STUDIO350 Скачать руководство пользователя страница 150

Страница: 150 / 286

e-STUDIO350/450 LASER OPTICAL UNIT

8 - 10

November 2003 © TOSHIBA TEC

(7)

Remove 3 screws with spring. Lift up the laser

optical unit, avoiding contact with the laser unit

fan.

Note:

1. Do not leave fingerprints or stain on the slit

glass.

2. Laser optical unit is a precise apparatus.

Handle the unit with extra care not to shock

or vibrate it.

3. Never attempt to disassemble the unit in

the field since it is very sensitive to the dust

and stain.

4. When installing, fix the laser optical unit with

the screws securely by matching the

bosses on the bottom of the unit with the

holes of the frame.

Fig. 8-604

Fig. 8-605

[C] LRL PC board

(1)

Take off the receiving tray

(

Chapter 2.5.1 [H]).

(2)

Disconnect 2 connectors with lock (CN204 and

CN206) and 2 connectors (CN205 and

CN207).

(3)

Remove 1 screw. Take off the LRL PC board

by releasing 2 locking supports.

[B] Laser unit fan

(1)

Take off the receiving tray

(

Chapter 2.5.1 [H]).

(2)

Disconnect 1 connector.

(3)

Remove 2 screws and take off the laser unit

fan.

Fig. 8-606

Содержание e-STUDIO350






























































































































































































































































































Результаты поиска

Содержание e-STUDIO350

Отзывы:

Toshiba e-STUDIO350, Руководство по обслуживанию, Страница: 150 / 286

Результаты поиска

Содержание e-STUDIO350

Отзывы: