Toshiba e-STUDIO350 Скачать руководство пользователя страница 271

Страница: 271 / 286

November 2003 © TOSHIBA TEC

15 - 1

e-STUDIO350/450 POWER SUPPLY UNIT

15. POWER SUPPLY UNIT

15.1 Construction

The power supply unit consists of an AC filter and insulation type DC output circuits.

(1)

AC filter

Eliminates noise from the outside and prevents the noise generated by the equipment from leaking

to the outside.

(2)

DC output circuits

Converts AC voltage input from outside to DC voltage and supplies it to each electric part. The DC

voltage is divided into the following two lines.

a. Main line

: Power supply used in the entire equipment during image forming process.

Five kinds of voltage (+3.3V, +5.1V, +12V, –12V and +24V) are output when

the main switch of the equipment is turned ON.

b. Door switch line : Power supply used in the entire equipment during image forming process,

being supplied via the door switch. Two kinds of voltage (+5.1VD and +24VD)

are output only when the main switch of the equipment is turned ON and two

doors (front cover and jam access cover) are closed.

15.2 Operation of DC Output Circuits

(1)

Starting line output

When the main switch of the equipment is turned ON, power starts supplying to all the lines only

when two doors (front cover and jam access cover) are closed.

(2)

Stopping line output

When the main switch of the equipment is turned OFF, PWR-DN signal is output after the instanta-

neous outage insurance time (20 ms or more) elapses and then the supply of each voltage stops. If

the supply of voltage of the main line (+3.3VA, +5.1VA, +12VA, -12VA) stops earlier than the 24V

line does, it may cause the damage of the electron device on each control circuit. To prevent this,

the supply of these voltages stops after the PWR-DN signal is output and the minimum retaining

time (+3.3VA/+5.1VA: 50 ms or more, +12VA/-12VA: 5 ms or more) elapses.

(3)

Output protection

Each output system includes an overcurrent and overvoltage protection circuits (a fuse and internal

protection circuit). This is to prevent the defectives (damage or abnormal operation of the second-

ary circuit) which may be caused by an overcurrent due to a short circuit or an overvoltage due to a

short circuit between different voltages. If the protection circuit is activated (except the case the

fuse is blown out), remove the causes such as short-circuit. Turn ON the power again 1 minute later

to clear the overcurrent protection.

Содержание e-STUDIO350






























































































































































































































































































Результаты поиска

Содержание e-STUDIO350

Отзывы:

Toshiba e-STUDIO350, Руководство по обслуживанию, Страница: 271 / 286

Результаты поиска

Содержание e-STUDIO350

Отзывы: