manualshive.com logo in svg

Toshiba e-STUDIO350, Руководство по обслуживанию, Страница: 203 / 286

Поделиться
Скачать
Toshiba e-STUDIO350 Скачать руководство пользователя страница 203

November 2003 © TOSHIBA TEC

11 - 15

e-STUDIO350/450  DRUM RELATED SECTON

11

(H-2) Toner bag full detection sensor-2

(1)

Open the front cover.

(2)

Disconnect 1 connector and take off the toner

bag full detection sensor-2.

[I] Developer unit cooling fan

(I-1) Developer unit cooling fan-2

(1)

Take off the rear cover ( 

 Chapter 2.5.1 [C]).

(2)

Take off the SYS board with the whole case

( 

 Chapter 2.5.2 [C]).

(3)

Disconnect 1 connector and release the har-

ness from 1 harness clamp.

(4)

Remove 2 screws and take off the duct.

Fig. 11-624

Fig. 11-625

Fig. 11-626

Fig. 11-627

Developer unit
cooling fan-2

(5)

Release the harness from 1 harness clamp.

(6)

Remove 1 screw and take off the duct cover.

(7)

Take off the developer unit cooling fan-2.

Note:

When installing, pay attention to the direction

of the wind from the fan.

Содержание e-STUDIO350































































































































































































































































































Отзывы:

Нет отзывов