Toshiba e-STUDIO350 Скачать руководство пользователя страница 112

Страница: 112 / 286

e-STUDIO350/450 SCANNER

6 - 4

November 2003 © TOSHIBA TEC

6.3

Description of Operation

6.3.1 Scan motor

(a) Scanning of an original placed on the original glass

This motor drives the carriages-1 and -2 through the timing belt and carriage wire. First, the scan

motor drives the carriages-1 and -2 to their respective home position. The home position is de-

tected when the carriage-1 passes the home position sensor. When the [START] button is pressed,

the both carriages start to move and scan the original on the glass.

(b) Scanning of an original placed on the RADF

The carriage-1 stays at the shading position during shading correction, and at the scanning

position during scanning operation.

Fig. 6-301

Wire pulley

Scan motor

Carriage-1

Motor speed-reduction pulley

Motor pulley

Carriage-2

Idler pulley

Содержание e-STUDIO350






























































































































































































































































































Результаты поиска

Содержание e-STUDIO350

Отзывы:

Toshiba e-STUDIO350, Руководство по обслуживанию, Страница: 112 / 286

Результаты поиска

Содержание e-STUDIO350

Отзывы: