Toshiba e-STUDIO350 Скачать руководство пользователя страница 138

Страница: 138 / 286

e-STUDIO350/450 IMAGE PROCESSING

7 - 8

November 2003 © TOSHIBA TEC

(4)

Gamma correction

This function corrects the input/output characteristics of the scanner/printer and adjusts the image

signals so that the input/output characteristics would match with the copy mode.

(5)

Gradation processing

This function switches the type of gradation processing depending on the copy mode: A type which

selects the printer characteristics giving the priority to resolution such as for text data, and another

which selects the printer characteristics giving the priority to gradation reproducibility such as for

photographic images.

(6)

External output system interface

This function controls the output of the output interface.

(7)

Scanner high quality image processing

This function corrects the image signals scanned by the scanner and reproduces them in a higher

image quality.

Содержание e-STUDIO350






























































































































































































































































































Результаты поиска

Содержание e-STUDIO350

Отзывы:

Toshiba e-STUDIO350, Руководство по обслуживанию, Страница: 138 / 286

Результаты поиска

Содержание e-STUDIO350

Отзывы: