manualshive.com logo in svg

Toshiba e-STUDIO350, Руководство по обслуживанию, Страница: 183 / 286

Поделиться
Скачать
Toshiba e-STUDIO350 Скачать руководство пользователя страница 183

November 2003 © TOSHIBA TEC

10 - 1

e-STUDIO350/450  DRIVE SYSTEM

10

10. DRIVE SYSTEM

10.1 General Description

The drive system drives the drum, developer unit, cleaner unit, fuser unit, transport roller, feed roller

(upper/lower drawer and bypass unit) and registration roller.

The drive system is driven by the rotation of the main motor.

(27)

(36/21)

(22)

(25/14)

(23)

(24)

(50/27)

(72/30)

(23)

(64/30)

(33)

(47)

(25)

(28/25)

(24)

(10)

10.2 Functions

A:

Drum drive ........................ Drives the drum by transmitting the rotation of the main motor

through the gears to the drum flange gear.

B:

Developer unit drive .......... Drives the developer unit by transmitting the rotation of the main

motor through the gears and clutch to the developer unit gears.

C:

Fuser unit drive ................. Drives the fuser unit by transmitting the rotation of the main motor

through the gears to the fuser unit gears.

D:

Cleaner unit drive ............. Drives the cleaner unit gear by the rotation of the drum flange gear.

E:

Registration roller drive ..... Drives the registration rollers by transmitting the rotation of the

main motor through the gears and clutches.

F:

Transport roller drive ......... Drives the transport roller by transmitting the rotation of the main

motor through the gears and clutches.

G:

Feed roller drive ................ Drives the cassette feed roller by transmitting the rotation of the

main motor through the gears and clutches.

A: Drum drive gear
D: Cleaner unit drive gear

B: Developer unit

drive gear

C: Fuser unit drive gear

E: Registration

roller drive gear

F: Transport roller drive gear
G: Feed roller drive gear

Main motor

Drum

Fig. 10-101

Содержание e-STUDIO350































































































































































































































































































Отзывы:

Нет отзывов