manualshive.com logo in svg

Toshiba e-STUDIO350, Руководство по обслуживанию, Страница: 73 / 286

Поделиться
Скачать
Toshiba e-STUDIO350 Скачать руководство пользователя страница 73

November 2003 © TOSHIBA TEC

3 - 5

e-STUDIO350/450  COPY PROCESS

3

•

Switching of developer bias polarity
With the area which has no negative charge,
background fogging is decreased by switching the
bias to the positive polarity (approx. +150 V).

•

Developer material
The developer material consists of a mixture of
the toner and carrier. The toner is charged to
the negative polarity and the carrier to positive
polarity due to the friction with each other
caused by mixing.
Tone

: Mainly consists of the resin and carbon.

Carrier : Consists of the ferrite and resin coating

on its surface to provide consistent fric-
tional electrification.

Note:

If the developer material is used for a long time (be-
yond its normal life span),
the toner is caked onto the carrier.

È

The charging performance of the carrier is lowered.
Symptom : 1.Image density is lowered.

2.Toner scattering occurs.
3.Background fogging occurs.

Solution : Replace the developer material.

•

 Magnetic roller
- Magnetic brush development -
The south and north poles are arranged inside
the magnetic roller as shown in the right figure.
The developer material forms a brush-like fluff
which contacts the photoconductive drum sur-
face.

È

This is caused by the magnetic force lines be-
tween the south and north poles.

Carbon
(5-10%)

Resin (90-95%)

[Toner]

5-20 µm

Ferrite

30-100 µm

[Carrier]

Fig.3-210

Toner

Carrier

No frictional electrification
occurs on the area where the
toner is caked.

Fig.3-211

N

S

S

Magnetic force
line

Magnetic roller

Photoconductive
drum

Fig.3-212

Содержание e-STUDIO350































































































































































































































































































Отзывы:

Нет отзывов