Toshiba e-STUDIO350 Скачать руководство пользователя страница 172

Страница: 172 / 286

e-STUDIO350/450 PAPER FEEDING SYSTEM

9 - 22

November 2003 © TOSHIBA TEC

SYS board upper cover

Fig. 9-450

Fig. 9-449

[D] Registration roller

(1)

Take off the bypass unit (

Chapter 9.4 (A-1)).

(2)

Take off ADU (

Chapter 14.5 [A]).

(3)

Take off the front cover (

Chapter 2.5.1 [A]).

(4)

Take off the cleaner unit

(

Chapter 11.6 [A]).

(5)

Take off the rear cover (

Chapter 2.5.1 [H]).

(6)

Take off the right rear cover

(

Chapter 2.5.1 [G]).

(8)

Loosen 5 screws, disconnect 2 connectors

and slide the SYS board lower cover to take it

off.

Note:

Do not vibrate the cover because HDD is

attached on it.

(9)

Release the lock support on the upper side of

SYS board case and disconnect 4 connec-

tors.

(7)

Loosen 9 screws of the SYS board case and

slide the SYS board upper cover to take it off.

Fig. 9-448

SYS board lower cover

Содержание e-STUDIO350






























































































































































































































































































Результаты поиска

Содержание e-STUDIO350

Отзывы:

Toshiba e-STUDIO350, Руководство по обслуживанию, Страница: 172 / 286

Результаты поиска

Содержание e-STUDIO350

Отзывы: