Toshiba e-STUDIO350 Скачать руководство пользователя страница 132

Страница: 132 / 286

e-STUDIO350/450 IMAGE PROCESSING

7 - 2

November 2003 © TOSHIBA TEC

Image of an original placed on the original table is scanned by the optical system. The CCD (Charge

Coupled Device) reads the optical image signals and converts them into the electrical signals. The

electrical signals are amplified and undergo analog-to-digital conversion, then are changed into digital

signals. Shading correction (correction of variance in CCD elements and the light source) is performed

and the digital signal is output as an image signal from the scanning section.

The image processing section inputs the image signal from the scanning section and applies various

image processing on the signal, then transmits the output result to the writing section.

Images are processed by the SLG board (PWA-F-SLG-360) and LGC board (PWA-F-LGC-360) in this

equipment. The image signal read in the scanning function is processed in SLG board and the printer

image signal is processed in the SYS board.

CCD

A/D

conversion

Shading

correction

Signal

amplification

to image
processing
section

Fig. 7-102

Содержание e-STUDIO350






























































































































































































































































































Результаты поиска

Содержание e-STUDIO350

Отзывы:

Toshiba e-STUDIO350, Руководство по обслуживанию, Страница: 132 / 286

Результаты поиска

Содержание e-STUDIO350

Отзывы: