Toshiba e-STUDIO350 Скачать руководство пользователя страница 214

Страница: 214 / 286

e-STUDIO350/450 DEVELOPMENT SYSTEM

12 - 6

November 2003 © TOSHIBA TEC

Drive

winding

Detection

winding

conversion

circuit

Auto-toner

output

To the main
CPU(LGC board)

ATS

Magnetic circuit

Magnetic resistance

(Developer material)

(2)

Function of auto-toner sensor

The auto-toner sensor consists of the following circuits:

· Drive winding

: A magnetic head (primary side) with a high-frequency magnetic field, which

forms a magnetic circuit in the developer material.

· Detection winding

: Receives the change in the magnetic resistance of the developer material

through the magnetic circuit (secondary side).

· DC conversion circuit : Converts a high-frequency output from the detection winding into a DC

signal (auto-toner output V

ATS

When the toner density is low—

The ratio of the toner against the carrier in the developer material decreases.

→

The magnetic resistance decreases.

→

The detection output increases.

→

The auto-toner output V

ATS

increases.

When the toner density is high—

The ratio of the toner against the carrier in the developer material increases.

→

The magnetic resistance increases.

→

The detection output decreases.

→

The auto-toner output V

ATS

decreases.

Fig. 12-402

Содержание e-STUDIO350






























































































































































































































































































Результаты поиска

Содержание e-STUDIO350

Отзывы:

Toshiba e-STUDIO350, Руководство по обслуживанию, Страница: 214 / 286

Результаты поиска

Содержание e-STUDIO350

Отзывы: