Toshiba e-STUDIO350 Скачать руководство пользователя страница 125

Страница: 125 / 286

November 2003 © TOSHIBA TEC

6 - 17

e-STUDIO350/450 SCANNER

[D] Exposure lamp

(1)

Take off the original glass (

Chapter 6.7 [A]).

(2)

Take off the front upper cover (

Chapter

2.5.1 [E]).

(3)

Move the carriage-1 to the center position

where the side of the frame is cut out.

(4)

Disconnect 1 connector from the INV board.

(5)

Release the harness from 1 harness clamp

and pull out the harness from the frame of the

carriage.

Note:

When disconnecting the connector, make sure

not to overload the carriage frame.

(6)

Move the carriage-1 to the position where the

exposure lamp is seen through the cutout of

the frame.

(C-2)

LT series

(1)

Take off the lens cover (

Chapter 6.7 [B]).

(2)

Disconnect 1 connector from the SLG board.

(3)

Release the harnesses from 6 harness clamps.

(4)

Remove 1 screw each and take off the APS

sensors (4 pcs.).

Fig. 6-704L

Fig. 6-705

Fig. 6-706

Fig. 6-707

Содержание e-STUDIO350






























































































































































































































































































Результаты поиска

Содержание e-STUDIO350

Отзывы:

Toshiba e-STUDIO350, Руководство по обслуживанию, Страница: 125 / 286

Результаты поиска

Содержание e-STUDIO350

Отзывы: