Toshiba e-STUDIO350 Скачать руководство пользователя страница 180

Страница: 180 / 286

e-STUDIO350/450 PAPER FEEDING SYSTEM

9 - 30

November 2003 © TOSHIBA TEC

Fig. 9-481

Fig. 9-480

Fig. 9-479

(3)

Remove 2 screws and take off the clutch

bracket and bush.

Fig. 9-478

(H-8) Drawer feed clutch

(1)

Take off the drawer feeding unit (

Chapter

10.4 (H-1)).

(2)

Disconnect the connector and release the har-

ness from harness clamp.

(3)

Remove 3 E-rings, pulley, one-way clutch and

take off the pickup roller.

Notes:

Match the protruding portion of clutch with the

position shown in the drawing for assembling.

(4)

Loosen 1 setscrew and take off the drawer

feed clutch.

E-ring

One-way clutch

Pickup roller

Pulley

E-ring

Connector

Bush

Clutch bracket

Drawer feed clutch

Setscrew

Содержание e-STUDIO350






























































































































































































































































































Результаты поиска

Содержание e-STUDIO350

Отзывы:

Toshiba e-STUDIO350, Руководство по обслуживанию, Страница: 180 / 286

Результаты поиска

Содержание e-STUDIO350

Отзывы: