Toshiba e-STUDIO350 Скачать руководство пользователя страница 193

Страница: 193 / 286

November 2003 © TOSHIBA TEC

11 - 5

e-STUDIO350/450 DRUM RELATED SECTON

11.3 Output Control Circuits of High-Voltage Transformer

11.3.1 Overview

• Generate the output control voltage Vc of the main charger, transfer/separation charger, transfer guide

bias and developer bias.

• Convert Vc

The current is output linearly.

11.3.2 Description of operations

• Outputs the adjustment value of the main, transfer and separation chargers, developer bias and transfer

guide bias in the NVRAM to the ASIC GA.

↓

• Outputs the control voltage data from the ASIC GA to the D/A converter.

↓

• Converts to the analog data by the D/A converter.

↓

• Outputs the control voltage Vc to the main, transfer and separation chargers, developer bias and trans-

fer guide bias transformer.

↓

• The main, transfer and separation chargers, developer bias and transfer guide bias transformer gener-

ate output current or voltage which is proportional to the control voltage Vc.

* Adjustment of the control voltage Vc (change of adjustment data) is performed in the adjustment

mode (05).

* The output value of the transfer guide bias is fixed when the high-voltage transformer is shipped from

the factory.

Fig. 11-301

HVT board

IC32

IC38

IC2

NVRAM

LGC board

ASIC

Output

Main/
transfer/
separation/
chargres,
developer
bias and
transfer
guide bias

D/A
conveter

Digital
data

Adijustment
value

Analog

Содержание e-STUDIO350






























































































































































































































































































Результаты поиска

Содержание e-STUDIO350

Отзывы:

Toshiba e-STUDIO350, Руководство по обслуживанию, Страница: 193 / 286

Результаты поиска

Содержание e-STUDIO350

Отзывы: