Toshiba e-STUDIO350 Скачать руководство пользователя страница 246

Страница: 246 / 286

e-STUDIO350/450 FUSER UNIT / PAPER EXIT SECTION

13 - 22

November 2003 © TOSHIBA TEC

Fig. 13-725

(7) Take out the fuser roller with the bushing from

the front side.

(8) Remove C-ring and bushing from the fuser roller.

Fig. 13-726

Notes:

When reassembling, pay attention to the fol-
lowings.
1. When inserting the fuser roller, be careful

not to deform the thermistors.

2. Be careful of the installation direction of the

gear (the direction of the protrusion inside
the gear).

3. Make sure not to scratch the fuser roller.

Lay the fuser roller on the clean place and
prevent the fuser roller from dust.

4. When the fuser roller has been replaced,

make sure to clean the separation fingers
for the fuser roller.

Fig. 13-727

[K] Thermistor

(1) Take off the fuser roller (

Chapter 13.7 [J]).

(2) Release the harnesses from 4 harness

clamps.

(3) Remove 1 screw for each thermistor. Then

take off the main thermistor and edge ther-
mistor.

Note:

When installing, be careful not to deform the
thermistors or the frame (plate).

C-ring

Bushing

Outer side
(C-ring side)

Inner side

(Bushing side)

Protrusion

Содержание e-STUDIO350






























































































































































































































































































Результаты поиска

Содержание e-STUDIO350

Отзывы:

Toshiba e-STUDIO350, Руководство по обслуживанию, Страница: 246 / 286

Результаты поиска

Содержание e-STUDIO350

Отзывы: