Toshiba e-STUDIO350 Скачать руководство пользователя страница 197

Страница: 197 / 286

November 2003 © TOSHIBA TEC

11 - 9

e-STUDIO350/450 DRUM RELATED SECTON

11.6 Disassembly and Replacement

[A] Cleaner unit

(1)

Open the front cover, take off the toner bag

and front cover(

Chapter 2.5.1 [A]).

(2)

Take off the developer unit(

Chapter 12.5 [A]).

(3)

Open the bypass unit, ADU and jam access

cover.

(4)

Release the latch and remove the toner bag

full detection sensor-2.

(5)

Loosen 2 screws and take off the cleaner unit.

[B] Main charger

(B-1) Main charger

(1)

Take off the cleaner unit

(

Chapter 11.6 [A]).

(2)

Release the latch and pull out the main charger

to the direction of the arrow.

Note:

Be careful not to touch or scratch the drum

surface at this time.

(B-2) Main charger grid

(1)

Push the terminal head at the front side and

remove the grid.

Note:

Do not touch the mesh area of the grid.

(B-3) Main charger wire

* Length: 363 mm (tungsten wire) diameter:

0.06 mm

(1)

Take off each terminal cover of the front and

rear sides.

Fig. 11-601

Fig. 11-602

Fig. 11-603

Fig. 11-604

Содержание e-STUDIO350






























































































































































































































































































Результаты поиска

Содержание e-STUDIO350

Отзывы:

Toshiba e-STUDIO350, Руководство по обслуживанию, Страница: 197 / 286

Результаты поиска

Содержание e-STUDIO350

Отзывы: