Toshiba e-STUDIO350 Скачать руководство пользователя страница 154

Страница: 154 / 286

e-STUDIO350/450 PAPER FEEDING SYSTEM

9 - 4

November 2003 © TOSHIBA TEC

(9)

Drawer paper stock sensor

This is a transmissive-type sensor which detects the amount of paper remaining in the drawer

using an actuator. When the remaining paper has become around 100 sheets, the actuator blocks

the light path of the sensor to notify that the paper quantity is getting less.

(10) Feed sensor

This sensor detects whether the leading/trailing edge of paper has passed the feed roller or not. It

also detects jams such as paper misfeeding.

(11) Registration sensor

This sensor detects whether the leading edge of the paper has reached the registration roller or

not, and the trailing edge of paper has passed the registration roller or not.

Содержание e-STUDIO350






























































































































































































































































































Результаты поиска

Содержание e-STUDIO350

Отзывы:

Toshiba e-STUDIO350, Руководство по обслуживанию, Страница: 154 / 286

Результаты поиска

Содержание e-STUDIO350

Отзывы: