Toshiba e-STUDIO350 Скачать руководство пользователя страница 49

Страница: 49 / 286

November 2003 © TOSHIBA TEC

2 - 33

e-STUDIO350/450 OUTLINE OF THE MACHINE

Fig. 2-535

[D] Switching power supply

(1)

Take off the left cover (

Chapter 2.5.1 [J]).

(2)

Remove 2 screws. Disconnect 2 connectors

with lock on the front side and 1 connector

while releasing the harness from the holder

on the right side of the bracket.

(3)

Disconnect 3 connectors while the switching

power supply is pulled out to the front and take

off the switching power supply.

Fig. 2-533

Fig. 2-532

Fig. 2-534

(6)

Remove 12 screws, take off the NIC board

and SYS board.

SYS board

NIC board

[E]

Power supply cooling fan

(1)

Take off the left cover (

Chapter 2.5.1 [J]).

(2)

Remove 2 screws and take off the power sup-

ply cooling fan on the switching power sup-

ply.

Note:

When installing, pay attention to the direction

of the wind from the fan.

Содержание e-STUDIO350






























































































































































































































































































Результаты поиска

Содержание e-STUDIO350

Отзывы:

Toshiba e-STUDIO350, Руководство по обслуживанию, Страница: 49 / 286

Результаты поиска

Содержание e-STUDIO350

Отзывы: