Toshiba e-STUDIO350 Скачать руководство пользователя страница 124

Страница: 124 / 286

e-STUDIO350/450 SCANNER

6 - 16

November 2003 © TOSHIBA TEC

6.7

Disassembly and Replacement

[A] Original glass

(1)

Take off the right upper cover (

Chapter

2.5.1 [F]).

(2)

Remove 2 screws and take off the fixing

bracket.

[B] Lens cover

(1)

Take off the original glass (

Chapter 6.7 [A]).

(2)

Remove 6 screws and take off the lens cover.

[C] Automatic original detection sensor

(APS sensor)

(C-1) A4 series

(1)

Take off the lens cover (

Chapter 6.7 [B]).

(2)

Disconnect 1 connector from the SLG board.

(3)

Release the harnesses from 6 harness clamps.

(4)

Remove 1 screw each and take off the APS

sensors (5 pcs.).

(3)

Take off the original glass.

Note:

When installing, fit 2 small protrusions of the

original glass in the groove of the equipment

and fix the original glass with the fixing bracket

by pushing it to the left rear direction.

Original glass

Fig. 6-701

Fig. 6-702

Fig. 6-703

Fig. 6-704A

Protrusion

Содержание e-STUDIO350






























































































































































































































































































Результаты поиска

Содержание e-STUDIO350

Отзывы:

Toshiba e-STUDIO350, Руководство по обслуживанию, Страница: 124 / 286

Результаты поиска

Содержание e-STUDIO350

Отзывы: