Toshiba e-STUDIO350 Скачать руководство пользователя страница 205

Страница: 205 / 286

November 2003 © TOSHIBA TEC

11 - 17

e-STUDIO350/450 DRUM RELATED SECTON

[J]

Middle fan

(1)

Open the front cover. Take off the toner bag,

toner cartridge, developer unit and cleaner unit

(

Chapters 12.5 [A] and 11.6 [A]).

(2)

Take off the receiving tray and tray back cover

(

Chapter 2.5.1 [H][I]).

(3)

Take off the toner cartridge drive unit and

discharge LED (

Chapter 12.5 [I][G]).

(4)

Remove 1 screw and take off the toner bag

holder.

(5)

Remove 2 screw and take off the toner car-

tridge cover.

(6)

Take off the rear cover, SYS board case, de-

veloper unit cooling fan-2 and developer unit

cooling fan unit-1

(

Chapters 2.5.1 [C], 2.5.2 [C] and 11.6 [I]).

(7)

Take off the registration clutch and gear unit

(

Chapter 10.4 [B][C]).

(8)

Remove 3 screws on the rear side.

(9)

Remove 3 screws on the front side and

release the harnesses from 3 harness clamps.

(10) Take off the bracket of the toner cartridge.

Fig. 11-633

Fig. 11-631

Toner cartridge cover

Toner bag holder

Fig. 11-632

Содержание e-STUDIO350






























































































































































































































































































Результаты поиска

Содержание e-STUDIO350

Отзывы:

Toshiba e-STUDIO350, Руководство по обслуживанию, Страница: 205 / 286

Результаты поиска

Содержание e-STUDIO350

Отзывы: