Toshiba e-STUDIO350 Скачать руководство пользователя страница 248

Страница: 248 / 286

e-STUDIO350/450 FUSER UNIT / PAPER EXIT SECTION

13 - 24

November 2003 © TOSHIBA TEC

[N] IH board cooling fan

(1) Take off the IH control PC board with the

whole bracket (

Chapter 13.7 (M-2)).

(2) Remove 1 screw and take off the fan cover.

Fig. 13-733

Fig. 13-734

(M-2) IH board unit

(1) Take off the IH terminal cover. Disconnect

1 connector with lock and 2 faston terminals
(

Chapters 2.5.1 [L] and 13.7 [A]).

(2) Take off the right rear cover

(

Chapter 2.5.1 [P]).

(3) Take off the SYS board with the whole case

(

Chapter 2.5.2 [C]).

(4) Take off the IH board cover

(

Chapter 13.7 (M-1)).

(5) Disconnect 3 connectors and remove

2 screws, and then take off the IH board with
the whole bracket.

Fig. 13-732

(5) Disconnect 2 connectors with lock and 4 con-

nectors.

(6) Remove 4 screws and take off the IH board.

Cautions:

1. Tighten 2 screws (A) of the IH coil power

supply harness completely (tightening
torque: 1.17 - 1.56 N·m).

2. Since the IH control board is a high-

voltage section, make sure to pull out the
power cable at maintenance.

Connector with lock

Screw (A)

Содержание e-STUDIO350






























































































































































































































































































Результаты поиска

Содержание e-STUDIO350

Отзывы:

Toshiba e-STUDIO350, Руководство по обслуживанию, Страница: 248 / 286

Результаты поиска

Содержание e-STUDIO350

Отзывы: