Toshiba e-STUDIO350 Скачать руководство пользователя страница 80

Страница: 80 / 286

e-STUDIO350/450 GENERAL OPERATION

4 - 2

November 2003 © TOSHIBA TEC

4.2.2 Ready state (ready for copying)

•

Buttons on the control panel enabled

•

When no button is pressed for a certain period of time,

– Set number “1” and reproduction ratio “100%” are displayed. Equipment returns to the normal

ready state.

4.2.3 Drawer feed copying (Upper drawer paper feeding)

(1)

Press the [START] button

•

“READY” changes to “COPYING”

•

Exposure lamp ON

•

Scan motor ON

→

carriages -1 and -2 move forward

•

Polygonal motor rotates in high speed

•

Main motor and exit motor ON

– The drum, fuser unit, developer unit and exit roller are driven.

(2)

Drawer paper feeding

•

Main charger, developer bias and discharge LED ON

•

Fans are rotated in high speed

•

Drawer feed clutch ON

– The pickup roller, feed roller, separation roller and transport roller start to rotate.

•

Paper reaches the upper drawer feed sensor

– The upper drawer feed sensor is turned ON.

•

Paper reaches the registration roller.

– The registration sensor is turned ON and aligning is performed.

•

Drawer feed clutch OFF after a certain period of time

(3)

After the carriage operation:

•

Registration clutch ON after a certain period of time

→

paper is transported to the transfer area.

•

Copy counter operates

(4)

After the registration clutch is turned ON:

•

Transfer charger ON after a certain period of time

(5)

Completion of scanning

•

Scan motor OFF

•

Exposure lamp OFF

•

Registration clutch OFF (after the trailing edge of the paper passed the registration roller)

•

“READY (PRINTING)” is displayed

Содержание e-STUDIO350






























































































































































































































































































Результаты поиска

Содержание e-STUDIO350

Отзывы:

Toshiba e-STUDIO350, Руководство по обслуживанию, Страница: 80 / 286

Результаты поиска

Содержание e-STUDIO350

Отзывы: