Toshiba e-STUDIO350 Скачать руководство пользователя страница 78

Страница: 78 / 286

e-STUDIO350/450 COPY PROCESS

3 - 10

November 2003 © TOSHIBA TEC

Process

1. Photoconductive drum

(1) Sensitivity

(2) Surface potential

2. Charging

(1) Grid voltage

3. Data writing

(1) Light source

(2) Light amount

4. Development

(1) Magnetic roller

(2) Auto-toner

(3) Toner supply

(4) Toner-empty detection

(5) Toner

(6) Developer material

(7) Developer bias

5. Transfer

(1) Transfer bias

6. Separation

7. Discharge

(1) Discharging position

(2) Discharge LED

8. Cleaning

(1) Method

(2) Recovered toner

9. Fusing

(1) Method

(2) Cleaning

(3) Heater

3.3 Comparison with DP4500/3500

DP4500/3500

OD-3500 (OPCø60)

Highly sensitized/durable drum

-750 V

Scorotron method

-790 V

Semiconductor laser (Adjustment not

required)

4.0 nJ/mm

One magnetic roller

Magnetic bridge-circuit method

Toner cartridge

Density detection method

T-3500, T-3500E, T-3500D

D-3500

DC-550 V Adjustable output (during

printing)

DC+150 V Fixed (others)

Adjustable output (Constant current)

+580 V (Adjustment not required)

AC: Adjustable output (Constant voltage)

DC: Adjustment not required

Exposure after cleaning

Red LED

Cleaning blade

Not reusable

Long-life fuser roller method

Fuser roller:

Coated with fluoroplastic (ø40)

Pressure roller:

PFA tube roller (ø30)

Cleaning roller for pressure roller

(ø14)

IH coil (Induction-heating method)

Turned ON/OFF by thermistor

e-STUDIO350/450

←
←
←
←
←

←

4.3 nJ/mm

←
←
←
←

T-3520, T-3520E, T-3520D, T-3520C,

T-3520T

D-3500, D-3500C

←

←
←
←
←
←

←
←

Thin roller coated with fluoroplastic(ø40)

←
←
←
←
←

Содержание e-STUDIO350






























































































































































































































































































Результаты поиска

Содержание e-STUDIO350

Отзывы:

Toshiba e-STUDIO350, Руководство по обслуживанию, Страница: 78 / 286

Результаты поиска

Содержание e-STUDIO350

Отзывы: