manualshive.com logo in svg

Toshiba e-STUDIO350, Руководство по обслуживанию, Страница: 156 / 286

Поделиться
Скачать
Toshiba e-STUDIO350 Скачать руководство пользователя страница 156

e-STUDIO350/450  PAPER FEEDING SYSTEM

9 - 6

November 2003 © TOSHIBA TEC

9

9.2.3 Separation of paper

The separation roller in this equipment works to

separate the sheets of paper being fed. The sepa-

ration roller section consists of the feed roller, sepa-

ration roller, spring joint, etc. The feed roller rotates

in the direction of the white arrow (shown below in

the figure at right) at the same timing as the pickup

roller rotation when the feed clutch is turned ON.

When two sheets of paper are transported (shown

above in the figure at right), the lower sheet is

braked by the separation roller and not transported

any further and the upper sheet is transported in

the direction of black arrow since the frictional force

between two sheets is small.

(Example)

When only one sheet enters into the separation

roller section:

Since the transporting force of the feed roller is

greater than the braking force of the separation

roller, these two rollers rotate together to transport

the sheet to the registration roller.

When two sheets enter into the separation roller

section:

Since the transporting force of the feed roller and

the breaking force of the separation roller are

greater than the frictional force between two sheets,

the sheet A is transported in the direction of the

black arrow and the sheet B is braked by the sepa-

ration roller and is not transported any further.

Fig. 9-203

Fig. 9-204

Feed roller

Spring joint

Separation roller

Feed roller

Separation roller

Содержание e-STUDIO350































































































































































































































































































Отзывы:

Нет отзывов