Toshiba e-STUDIO350 Скачать руководство пользователя страница 198

Страница: 198 / 286

e-STUDIO350/450 DRUM RELATED SECTON

11 - 10

November 2003 © TOSHIBA TEC

(2)

Remove the terminal, spring and wire.

Notes:

Be careful of the followings when installing the wire.

Insert the wire securely into the V-grooves of

the front and rear sides.

Do not twist the wire.

Do not touch the wire directly with bare hands.

(B-4) Charger wire cleaning pad

(1)

Release the charger wire cleaner shaft from

the hooks of the charger wire cleaning pads.

(2)

Remove the charger wire cleaning pads.

Note:

When installing, make sure that 2 charger wire

cleaning pads are away from the wire while the

charger wire cleaner shaft is at the rear side.

[C] Drum

(1)

Pull out the cleaner unit and take off the main

charger (

Chapter 11.6 [A](B-1)).

(2)

Release the latch and remove the cleaner stay.

Fig. 11-605

Wire

Terminal

Spring

Fig. 11-606

Fig. 11-607

Fig. 11-608

Содержание e-STUDIO350






























































































































































































































































































Результаты поиска

Содержание e-STUDIO350

Отзывы:

Toshiba e-STUDIO350, Руководство по обслуживанию, Страница: 198 / 286

Результаты поиска

Содержание e-STUDIO350

Отзывы: